Operation Guide 3263

To toggle the Timekeeping Mode time between DST and Standard Time

DST indicator

1.

Use Dto display the current Home City Time (T-1)

 

screen.

 

 

 

 

 

2.

Hold down Auntil the seconds start to flash, which

 

 

indicates the setting screen.

 

 

3.

Press Cto display the DST setting screen.

 

4.

Press Dto toggle between Daylight Saving Time

 

 

( displayed) and Standard Time (

displayed).

 

5.

Press Ato exit the setting screen.

 

••The DST indicator appears on the Timekeeping screen to indicate that Daylight Saving Time is turned on.

12/24-Hour Format

••With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for times in the range of noon to 11:59 p.m. and no indicator appears to the left of the hour digits for times in the range of midnight to 11:59 a.m.

••With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without any indicator.

••The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is applied in all other modes.

Changing the City Setting of a Local Time

You can select any one of the city codes in the table at the back of this manual as a Local Time city.

1.Display the Local Time whose city setting you want to change, and then hold down Afor about one second until the current city code starts fo flash.

2.Use D(east) and B(west) to select the city code you want.

3.Press Cto display the DST setting screen.

4.Press Dto toggle between Daylight Saving Time (displayed) and Standard Time (displayed).

5.After the settings are the way you want, press A.

Swapping the Home City Time with a Local Time

You can use the procedure below to swap the current Home City Time (T-1) with one of the Local Times (T-2, T-3, T-4).

1.In the Timekeeping Mode, use Dto display the Local Time that you want to swap with the Home City Time.

2.Press Aand Bat the same time.

World Time

To set an alarm time

1.In the Alarm Mode, use Dto scroll through the alarm screens until the alarm number you want to set is

displayed.

2.After you select an alarm, hold down Auntil the hour setting of the alarm time

starts to flash, which indicates the setting screen.

••This operation turns on the One-time Alarm automatically.

3.Press Cto move the flashing in the sequence shown below to select other settings.

HourMinutes

One-time Alarm/Daily Alarm Selection

4. While a setting is flashing, use Dand Bto change it as described below.

Screen

To do this:

Do this:

 

 

 

 

Change the hour and

Use D(+) and B(–).

 

minutes.

••With the 12-hour format, set the time correctly

 

 

as a.m. or p.m. (P indicator).

 

 

 

/

Toggle between One-

Press D.

 

time Alarm and Daily

One-time Alarm on:

 

Alarm.

Daily Alarm on:

 

 

 

5. Press Ato exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the watch is in.

••Alarm and Hourly Time Signal operations are performed in accordance with the Home City Time (T-1).

••To stop the alarm tone after it starts to sound, press any button.

To test the alarm

In the Alarm Mode, hold down Dto sound the alarm.

City code

Current time and date in the zone of the selected city code

World Time shows the current time in 48 cities (31 time zones) around the world.

••All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.

To view the time for another city code

In the World Time Mode, press Dto scroll eastwardly through city codes.

••For full information about city codes, see the “City Code Table”.

••If the current time for a city is wrong, check your Timekeeping Mode time and time zone settings and make the necessary changes.

To turn an alarm on and off

1.In the Alarm Mode, use Dto select an alarm.

2.Press Ato cycle through the alarm settings as shown below.

Alarm Off

One-Time Alarm Daily Alarm On

 

On

••In all modes, the alarm on indicator is shown for the alarm that is currently turned on.

••The alarm on indicator flashes while the alarm is sounding.

To turn the Hourly Time Signal on and off

To toggle a city code time between Standard Time and Daylight Saving Time

DST indicator

1. In the World Time Mode, use D(east) to display the city

code (time zone) whose Standard Time/Daylight Saving

 

 

Time setting you want to change.

 

2. Hold down Afor about one second to toggle Daylight

 

Saving Time (DST displayed) and Standard Time (DST

 

not displayed).

 

••The DST indicator is on the display whenever you display

 

a city code for which Daylight Saving Time is turned on.

 

••Note that the DST/Standard Time setting affects only

 

the currently displayed city code. Other city codes are

 

not affected.

 

••Note that you cannot switch between Standard Time

 

and Daylight Saving Time while UTC is selected as the

 

city code.

Hourly time signal on

1.

In the Alarm Mode, use Dto select the Hourly Time

 

Signal.

indicator

 

2.

Press Ato toggle it on and off.

 

 

••The Hourly Time Signal on indicator is shown on the

 

display in all modes while this function is turned on.

Countdown Timer

To change your Home Time city to the current World Time city

1.In the World Time Mode, use Dto display the city you want to make your new Home Time city.

2.Press Aand Bat the same time.

••This makes the World Time city you selected in step 1 your new Home Time city.

Alarms

1/10 second

The countdown timer can be set within a range of one second to 24 hours. An alarm sounds when the countdown reaches zero.

••All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C.

Alarm on indicator

Alarm number

Alarm time (Hour : Minutes)

Your watch has a total of five alarms, each of which you can configure as a daily alarm or one-time alarm.

••Daily Alarm: Sounds at the preset time each day.

••One-time Alarm: Sounds once at the preset time and then is disabled automatically.

You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.

••All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.

••Alarms operate in coordination with the current Home City Time.

Hours

Minutes

Seconds

To configure the countdown timer

1.While the countdown start time is on the display in the Countdown Timer Mode, hold down Auntil the current countdown start time starts to flash, which indicates the

setting screen.

••If the countdown start time is not displayed, use the procedure under “To use the countdown timer” to display it.

2. Press Cto move the flashing in the sequence shown below to select other settings.

Hours Minutes Seconds

3.When the setting you want to change is flashing, use D(+) and B(–) to change

the flashing item.

••To specify a countdown start time of 24 hours, set.

4.Press Ato exit the setting screen.

2