Casio 3274 manual

MA1106-EA

Operation Guide 3274

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully.

Expose the watch to bright light to charge its capacitor before using it. You can use this watch even as its capacitor is being charged by exposure to bright light.

ξ Be sure to read “Power Supply” on page E-17 of this manual for important information you need to know when exposing the watch to bright light.

E-1

Keep the watch exposed to bright light

About This Manual

Bright Light

The electricity generated by the solar cell of the watch is stored by a built-in capacitor. Leaving or using the watch where it is not exposed to light causes the capacitor to run down. Make sure the watch is exposed to light as much as possible.

ξ When you are not wearing the watch on your wrist, position the face so it is pointed at a source of bright light.

ξ You should try to keep the watch outside of your sleeve as much as possible. Charging is reduced significantly if the

ξButton operations are indicated using the letters shown in the illustration.

ξTo ensure that this watch provides you with the years of

service for which it is designed, be sure to carefully read and follow the instructions under “Operating Precautions” and “User Maintenance”.

Solar cell face is only partially covered.

E-2 E-3

Contents

General Guide ..........................................................................................................	E-6
Timekeeping.............................................................................................................	E-8
Alarms ....................................................................................................................	E-10
Stopwatch ..............................................................................................................	E-14
Countdown Timer ..................................................................................................	E-15
Power Supply.........................................................................................................	E-17
Specifications ........................................................................................................	E-22

E-4

Procedure Lookup

The following is a handy reference list of all the operational procedures contained in this manual.

To set the time and date .........................................................................................	E-9
To set an alarm time..............................................................................................	E-11
To test the alarm....................................................................................................	E-12
To turn the Hourly Time Signal on and off..........................................................	E-13
To measure times with the stopwatch.................................................................	E-14
To use the countdown timer.................................................................................	E-15
To set the countdown start time ..........................................................................	E-16

E-5

General Guide

ξPress Bto change from mode to mode.

ξPressing Bafter performing some operations in any mode returns to the Timekeeping Mode.

ξIf you do not perform any operation for a few minutes in the Alarm Mode or Setting Screen, the watch automatically reverts to the Timekeeping Mode.

Timekeeping Mode	Alarm Mode	Stopwatch Mode	Countdown Timer Mode		Setting Screen
B	B		B	B
			B
E-6					E-7

Timekeeping

To set the time and date
Flashing	1. Press Bfour times in the Timekeeping Mode to display

Minutes

Hour Seconds

PM indicator Day

Day of week

In the Timekeeping Mode, press Cto switch between the 12-hour and 24-hour formats.

ξWhen the 12-hour format is selected, the indicator PM appears on the display to indicate “p.m.” times. There is no indicator for “a.m.” times.

ξWhen the 24-hour format is selected, the indicator 24H appears on the display.

ξA charge indicator appears on the display of this watch when charging is required.

the setting screen.
2. Press Ato move the selection (flashing) in the following
sequence.
	A		A
Seconds		Hour		Minutes
A					A
Day of week		Day		Month
	A		A

3.	While the seconds setting is selected (flashing), press Cto reset it to 00. If you
	press Cwhile the seconds setting is in the range of 30 to 59, the seconds are
	reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of
	00 to 29, the minutes count is unchanged.
4.	While any other setting is selected (flashing), press Cto increase the number.
	ξ Holding down Cchanges the setting at high speed.

Charge indicator

5. After you set the time and date, press Bto return to the Timekeeping Mode.

E-8 E-9