Operation Guide 3278/3279
• Signal reception may not be possible at the distances noted below during certain |
500 kilometers
500 kilometers
times of the year or day. Radio interference also may cause problems with reception. |
Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers |
Fukuoka/Saga
1,000 kilometers
Fukushima
1,000 kilometers
(310 miles) |
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers) |
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles) |
Shangqiu (China) transmitter: 1,500 kilometers (910 miles) |
• Even when the watch is within the reception range of the transmitter, signal |
Signals are receivable in the Taiwan area when reception conditions are good.
China Signal1,500 kilometers
500 kilometers
Chengdu
Shangqiu
Changchun Beijing
Shanghai
Hong Kong
reception will be impossible if the signal is blocked by mountains or other geological |
formations between the watch and signal source. |
• Signal reception is affected by weather, atmospheric conditions, and seasonal |
changes. |
• See the information under “Signal Reception Troubleshooting” (page |
experience problems with time calibration signal reception. |
|
|
The watch receives the time calibration signal automatically up to 6 times a day (5 times a day for the Chinese calibration signal). When any auto receive is successful, the remaining auto receive operations are not performed. The reception schedule (calibration times) depends on your currently selected Home City, and whether standard time or Daylight Saving Time is selected for your Home City.
| Your Home City |
| Auto Receive Start Times |
| |||
|
| 1 | 2 | 3 | 4 | 5 | 6 |
LIS | Standard Time | 1:00 am | 2:00 am | 3:00 am | 4:00 am | 5:00 am | Midnight* |
LON | Daylight Saving Time | 2:00 am | 3:00 am | 4:00 am | 5:00 am | Midnight* | 1:00 am* |
MAD | Standard Time | 2:00 am | 3:00 am | 4:00 am | 5:00 am | Midnight* | 1:00 am* |
PAR | Daylight Saving Time | 3:00 am | 4:00 am | 5:00 am | Midnight* | 1:00 am* | 2:00 am* |
ROM |
|
|
|
|
|
|
|
BER |
|
|
|
|
|
|
|
STO |
|
|
|
|
|
|
|
ATH | Standard Time | 3:00 am | 4:00 am | 5:00 am | Midnight* | 1:00 am* | 2:00 am* |
| Daylight Saving Time | 4:00 am | 5:00 am | Midnight* | 1:00 am* | 2:00 am* | 3:00 am* |
MOW | Standard Time | 4:00 am | 5:00 am | Midnight* | 1:00 am* | 2:00 am* | 3:00 am* |
| Daylight Saving Time | 5:00 am | Midnight* | 1:00 am* | 2:00 am* | 3:00 am* | 4:00 am* |
| Your Home City |
| Auto Receive Start Times |
| |||
|
| 1 | 2 | 3 | 4 | 5 | 6 |
HKG | Standard Time and | 1:00 am | 2:00 am | 3:00 am | 4:00 am | 5:00 am |
|
BJS | Daylight Saving Time |
|
|
|
|
|
|
TPE | Standard Time | Midnight | 1:00 am | 2:00 am | 3:00 am | 4:00 am | 5:00 am |
SEL |
|
|
|
|
|
|
|
TYO |
|
|
|
|
|
|
|
HNL | Standard Time and | Midnight | 1:00 am | 2:00 am | 3:00 am | 4:00 am | 5:00 am |
ANC | Daylight Saving Time |
|
|
|
|
|
|
YVR |
|
|
|
|
|
|
|
LAX |
|
|
|
|
|
|
|
YEA |
|
|
|
|
|
|
|
DEN |
|
|
|
|
|
|
|
MEX |
|
|
|
|
|
|
|
CHI |
|
|
|
|
|
|
|
NYC |
|
|
|
|
|
|
|
YHZ |
|
|
|
|
|
|
|
YYT |
|
|
|
|
|
|
|
|
|
|
|
|
|
| *Next day |
|
|
•When a calibration time is reached, the watch will receive the calibration signal only if it is in either the Timekeeping Mode or World Time Mode. Reception is not performed if a calibration time is reached while you are configuring settings.
•Auto receive of the calibration signal is designed to be performed early in the morning, while you sleep (provided that the Timekeeping Mode time is set correctly). Before going to bed for the night, remove the watch from your wrist, and put it in a location where it can receive the signal easily.
•The watch receives the calibration signal for two to seven minutes everyday when the time in the Timekeeping Mode reaches a calibration time. Do not perform any button operation within seven minutes before or after the calibration times. Doing so can interfere with correct calibration.
•Remember that reception of the calibration signal depends on the current time in the Timekeeping Mode. The receive operation will be performed whenever the display shows any one of the calibration times, regardless of whether or not the displayed time actually is the correct time.
The signal strength indicator shows the strength of the calibration signal being received. For best reception, be sure to keep the watch in a location where signal strength is strongest. The signal strength indicator is displayed while an auto or manual receive operation is in progress.
RCVD indicator
Signal strength indicator | Weak | Strong |
|
|
•Even in an area where signal strength is strong, it takes about 10 seconds for signal reception to stabilize enough for the indicator to indicate signal strength.
|
|
•Use the signal strength indicator as a guide for checking signal strength and for finding the best location for the watch during signal receive operations.
•Following reception of the time calibration signal and calibration of the watch’s time setting, the RCVD indicator will remain on the display in all modes. The RCVD indicator will not be displayed if signal reception was unsuccessful or after you adjust the current time setting manually.
•The RCVD indicator is displayed only when the watch is able to receive both time and date data successfully. It does not appear when only time data is received.
•The RCVD indicator indicates that at least one calibration signal receive operation (auto or manual) was successful during the current day. Note that the RCVD indicator disappears from the display each day when the first receive operation of the day is performed.
To perform manual receive
1. Enter the Timekeeping Mode (page
| Receiving | 2. Hold down D for about two seconds until the RCVD |
| indicator starts to flash on the display. This indicates |
| that manual receive is in progress. |
| • Time calibration signal reception takes from two to |
| seven minutes. Take care that you do not perform |
| any button operations or move the watch during this |
| time. |
•If the receive operation is successful, the reception
date and time appear on the display, along with the GET indicator.
3. After manual receive is complete, press D to return to normal timekeeping.
• The watch also will return to normal timekeeping if you do not perform any button operation for about one or two minutes.
If there was a previously successful reception
• If the latest reception fails but a previous reception was | To turn auto receive on and off |
|
| |
successful during the current day, the RCVD indicator |
| 1. In the Timekeeping Mode, press D to display the latest | ||
will be on the display. |
| successful receive time and date screen (page | ||
• The watch will return to normal timekeeping without |
| 2. Hold down A until the current auto receive setting ( |
| |
changing the time setting if you press D or if you do not |
| or | ) starts to flash. This is the setting screen. |
|
perform any button operation for about one or two |
| • Note that the setting screen will not appear if the |
| |
minutes. |
| currently selected Home City is one that does not |
| |
Note |
| support time calibration reception. |
| |
| 3. Press D to toggle auto receive on ( ) and off ( | ). | ||
• To interrupt a receive operation and return to normal |
| |||
| 4. Press A to exit the setting screen. |
| ||
timekeeping, press D. |
|
| ||
On/Off status | • For information about city codes that support signal |
| ||
|
| |||
receive, see “To specify your Home City” (page