Operation Guide 5022
Stopwatch
World Time
Stopwatch second hand
30
Stopwatch minute hand
Stopwatch 1/20 second hand
The stopwatch lets you measure elapsed time.
•When you enter the Stopwatch Mode, the stopwatch 1/20 second hand and the stopwatch minute hand move to 0.
•You can start elapsed time measurement with the stopwatch while the watch is in the Stopwatch Mode or the Timekeeping Mode.
•The display range of the stopwatch is 59 minutes, 59.95 seconds.
•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.
•You cannot switch to another mode while a stopwatch elapsed time operation is in progress.
Current time (hour) in the currently selected World Time city
City code
30
Minutes
The World Time Mode shows you the current time in 27 cities (29 time zones) around the world. A simple operation swaps your Home City with the currently selected World Time city.
•When you enter the World Time Mode, the stopwatch second hand will move automatically to the city code that is currently selected as the World Time city code. At the same time, the hour and minute hands will move to the current time in that city.
•The day of the week hand shows whether or not Daylight Saving Time (summer time) is turned off for the currently selected city code.
•If the current time shown for a city is wrong, check your Home City settings and make the necessary changes.
•All of the operations in this section are performed in the World Time Mode.
To start an elapsed time operation while in the Stopwatch Mode
1.In the Timekeeping Mode, press Dto enter the Stopwatch Mode.
2.In the Stopwatch Mode, press Bto start elapsed time measurement.
3.Press B to stop elapsed time measurement.
•You can restart and stop elapsed time measurement as many times as you like by pressing B.
•The 1/20 second hand rotates during the first 60 seconds only, and then stops. When elapsed timing is stopped (by pressing B), the 1/20 second hand jumps to the 1/20 second indication (which is kept internally).
4.Check the elapsed time.
• After you are finished measuring elapsed time, press D to reset the stopwatch to all |
zeros. The stopwatch will reset to all zeros even if you press D while elapsed time |
measurement is in progress. |
Seconds Day of the week hand
To view the time in another city
In the World Time Mode, use D to move the stopwatch second hand to the city code of the city you want to select as the World Time city.
•The hour hand, minute hand, and date display will change automatically to the applicable settings for the currently selected city code.
•All buttons (except for Cfor changing modes) are disabled while the hands and date display are changing.
•The watch will beep if the city code you select is your current Home City.
•For full information on city codes, see the “City Code Table”.
To toggle a city code time between Standard Time and Daylight Saving Time
• To return to the Timekeeping Mode, press D while the stopwatch is reset to all |
zeros. |
To start an elapsed time operation while in the Timekeeping Mode
1.In the Timekeeping Mode, press Bto start elapsed time measurement.
•After pressing Bin the Timekeeping Mode, elapsed time measurement will not start for about one second.
•The elapsed time operation will not start if you press Bin the Timekeeping Mode while either of the following conditions exists.
While an alarm is sounding
While the watch is changing from one date to the next (at midnight)
2.Press Bto stop elapsed time measurement.
•You can restart and stop elapsed time measurement as many times as you like by pressing B.
•The 1/20 second hand rotates during the first 60 seconds only, and then stops. When elapsed time measurement is stopped (by pressing B), the 1/20 second hand jumps to the 1/20 second indication (which is kept internally).
3.Check the elapsed time.
Day of the week hand
30
▲Hold down Afor three
▲ | seconds. |
|
1.In the World Time Mode, use D to select the city code whose Standard Time/Daylight Saving Time setting you want to change.
2.Hold down Afor about three seconds until the watch beeps. This will cause the day of the week hand to
toggle between ON (Daylight Saving Time) and OFF (Standard Time).
•Note that you cannot switch between Standard Time and Daylight Saving Time while GMT is selected as the city code.
•Note that the Standard Time/Daylight Saving Time setting affects only the currently displayed city code. Other city codes are not affected.
•The Standard Time/Daylight Saving Time setting of your Home City can be changed in the Timekeeping Mode only. See “To set the time and date manually” for more information.
•After you are finished measuring elapsed time, press D to reset the stopwatch to all zeros. The stopwatch will reset to all zeros even if you press D while elapsed time measurement is in progress.
•To return to the Timekeeping Mode, press D while the stopwatch is reset to all zeros.
Countdown Timer
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time city. This changes your Home City to your World Time city, and your World Time city to your Home City. This capability can come in handy when you frequently travel between two cities in different time zones.
• If your current World Time city supports receipt of a time calibration signal, making it |
your Home City enables calibration signal reception. |
Second hand
30
|
| Day of the |
|
| week hand |
▲ |
| |
You can set the countdown timer within a range of one to 60 minutes. An alarm sounds when the countdown reaches zero.
•Whenever you enter the Countdown Timer Mode, the day of the week hand initially will move to the TMR position. After about one second, the day of the week hand will move to the countdown start time (minutes) and stop there.
•In the Countdown Timer Mode, the timekeeping second hand points straight down (6 o’clock position).
•When you enter the Countdown Time Mode, the day of the week hand initially will point to countdown start time that was set the last time the Countdown Timer Mode was exited.
To swap your Home City and World Time city
1.In the World Time Mode, use D to select the World Time city you want.
2.Hold down Bfor about three seconds until the watch beeps.
•This will make the World Time city (which you selected in step 1), your Home City. At the same time, it will change the Home City you had selected prior to step 2 your World Time city.
•After swapping the Home City and World Time city, the watch stays in the World Time Mode with the city that was selected as the Home City prior to step 2 now displayed as the World Time city.
Alarm
30 |
|
Timekeeping | Minute hand |
| |
second hand |
|
Alarm time (minute) Mode indicator
When the alarm is turned on, the alarm sounds when the alarm time is reached.
• The day of the week hand points to AL while the watch |
is in the Alarm Mode. The stopwatch second hand points |
•The initial factory default setting for the countdown start time is 60 minutes. The day of the week hand points to 0 (or 60) when the countdown start time is 60 minutes.
•All of the operations in this section are performed in the Countdown Timer Mode.
To set the countdown start time
While the day of the week hand is stopped at the current countdown start time in the Countdown Timer Mode, press Ato advance the hand by one minute. Keep pressing
Auntil the hand is at the start time you want.
• Holding down Aat this time will move the hand at high speed. |
• If the day of the week hand does not move when you press A, it may mean that the |
watch is not indicating a countdown start time. If this happens, refer to “To use the |
countdown timer” and return to the countdown start time. |
• To set a countdown start time of 60 minutes, move the day of the week hand to 0 (or |
30
Alarm time (hour)
to the current alarm on (ON)/off (OFF) setting, while the |
hour, minute, and |
alarm time setting. |
• All of the operations in this section are performed in the |
Alarm Mode. |
To set an alarm time
1.In the Alarm Mode, hold down Afor about three seconds until the watch beeps. This indicates it is in the setting mode.
•The stopwatch second hand will move to ON (alarm on) at this time.
60). |
To use the countdown timer
Press Bwhile in the Countdown Timer Mode to start the countdown timer.
•When the end of the countdown is reached, the alarm will sound for 10 seconds or until you stop it by pressing any button. The countdown time is reset automatically to its starting value after the alarm stops.
•Press Bwhile a countdown operation is in progress to pause it. Press Bagain to resume the countdown.
•To stop a countdown operation completely, first pause it (by pressing B), and then press D. This will return the countdown time to its starting value.
•You will not be able to switch to another mode while a countdown is in progress.
2.Use D(+) and
•Each press of either button moves the hands
3.After setting the alarm time, press A to exit the setting mode.
• Setting the alarm time causes the alarm to turn on automatically.
• As you set the alarm time, take care to ensure that the
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the watch is in.
•Alarm operations are performed in accordance with the Timekeeping Mode time.
•Pressing any button stops the alarm tone operation.
To toggle an alarm on and off
In the Alarm Mode, press Ato toggle the alarm ON and OFF.
3