Operation Guide 5157
1.In the Calendar Mode, hold down Buntil the month digits start to flash, which indicates the setting screen.
2.Press Cto increase the month digits.
3.Press Bto move the selection to the day digits.
4.Press Cto increase the day digits.
5.Press Bto move the selection to the day of the week.
6.Press Cto advance to the next day.
7.Press Bto exit the setting screen.
ξThe watch does not make any allowance for leap years. Be sure to manually set February 29 when one occurs during a leap year.
Alarm
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset time each day. When the Hourly Time Signal is turned on, the watch beeps every hour on the hour.
ξYou can configure alarm settings and Hourly Time Signal settings in the Alarm Mode, which you enter by pressing C(page
|
|
To set the alarm time and to turn the Daily Alarm and Hourly Time Signal on and off
Mode indicator
Alarm on indicator |
|
|
|
|
|
|
| ||||
(OLD DOWN | 0RESSE |
| 0RESSE |
|
| ||||||
|
|
|
|
|
| ,EFT |
| 2IGHT |
| ||
|
|
|
|
|
|
| |||||
|
|
|
| (OUR |
|
| MINUTES |
|
| MINUTES |
|
|
|
|
|
|
|
| DIGIT |
|
| DIGIT |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| !LARM(OURLY 4IME43IGNAL SETTING |
|
|
| ||||
|
| 0RESSE |
| 0RESSE | |||||||
|
|
|
|
|
|
|
|
Alarm time (Hour : Minutes)
Hourly time signal on indicator
1.In the Alarm Mode, hold down Buntil the hour digits start to flash, which indicates the setting screen.
2.Press Cto increase the hour digits.
ξThe
3.Press Bto move the selection to the left minutes digit.
4.Press Cto increase the left minutes digit.
5.Press Bto move the selection to the right minutes digit.
6.Press Cto increase the right minutes digit.
7.Press Bto move to the Daily Alarm and Hourly Time Signal on and off setting.
8.Press Cto cycle through the Daily Alarm and Hourly Time Signal settings as shown in the sequence below.
ξAt this time Daily Alarm and Hourly Time Signal automatically turn on.
|
|
| Press |
| Press |
|
| Press |
|
|
| |
| C. |
| C. |
|
| C. |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Both ON | Both OFF | Daily Alarm only | Hourly Time | |||||||
|
|
|
|
|
|
|
|
| Signal only | |
|
|
|
|
|
|
|
|
|
|
|
Press C.
9. Press Bto exit the setting screen.
To stop the alarmPress any button to stop the alarm after it starts to sound.
Hold down Cin any mode (except when making any settings) to sound the alarm. Note that the alarm sound changes each time you hold down Cto test the alarm. There are a total of four different alarm sounds. The last alarm sound you hear when performing the above test is the one that is used for the Daily Alarm and the Hourly Time Signal.
ξNote that holding down Calso changes the mode.
|
|
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone.
ξIn the Dual Time Mode, the seconds count is synchronized with the seconds count of the Timekeeping Mode digital time.
To set the Dual Time
Mode indicator
(OLD DOWN | 0RESSE |
|
| 0RESSE | ||||
|
|
| (OUR |
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 0RESSE |
|
|
|
| ||
|
|
|
|
|
|
|
Hour Seconds
Minutes
|
|
1. In the Dual Time Mode, hold down Buntil the hour digits start to flash, which |
indicates the setting screen. |
Stopwatch
2. | Press Cto increase the hour digits. |
3. | Press Bto move the selection to the minutes digits. |
4. | Press Cto increase the minutes digits. |
5. | Press Bto move the selection to 12/24. |
6. | Press Cto toggle the timekeeping format between |
7. | Press Bto exit the setting screen. |
ξWith the
ξWith the
Mode indicator
Minutes 1/100 second
Seconds
The Stopwatch Mode lets you measure elapsed time. The range of the stopwatch is 59 minutes, 59.99 seconds.
ξThe stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.
ξThe stopwatch measurement operation continues even if you exit the Stopwatch Mode.
To use the Stopwatch
1.In the Stopwatch Mode, press Bto start the stopwatch.
2.Press Bto stop the time measurement.
ξYou can press Bas many times as you want to resume and stop timing.
3.After you are finished using the stopwatch, hold down Bto clear the stopwatch time to all zeros.