Operation Guide 4380 4396 5048

Countdown Timer

Timekeeping Mode timeHours Seconds

Minutes

Auto-repeat on indicator

You can set the countdown timer within a range of one minute to 24 hours. An alarm sounds when the countdown reaches zero.

You also can select auto-repeat, which automatically restarts the countdown from the original value you set whenever zero is reached.

All of the operations in this section are performed in theCountdown Timer Mode, which you enter by pressing

C.

4.While a setting is flashing, use D (+) and B (–) to change it.

To set an alarm that does not include a month (daily alarm, monthly alarm), set x for the month. Use D and B until the x mark appears (between 12 and 1) while month setting is flashing.

To set an alarm that does not include a day (daily alarm, 1-month alarm), set xx for the day. Use D and B until the xx mark appears (between the end of the month and 1) while the day setting is flashing.

When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (A indicator) or p.m. (P indicator).

5.Press A to exit the setting screen.
Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, until

To use the countdown timerPress D while in the Countdown Timer Mode to start the countdown timer.

When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is reset automatically to its starting value after the alarm stops.

When auto-repeat is turned on, the countdown will restart automatically without pausing when it reaches zero. The alarm sounds when the countdown reaches zero.

The countdown timer measurement operation continues even if you exit the Countdown Timer Mode.

Press D while a countdown operation is in progress to pause it. Press D again to resume the countdown.

To stop a countdown operation completely, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value.

To configure countdown start time and auto-repeat settings

 

 

 

 

 

 

 

 

 

1. While the countdown start time is on the display in the

 

 

 

 

 

 

 

Countdown Timer Mode, hold down A until the hour

 

 

 

 

 

 

 

setting of the countdown start time starts to flash, which

 

 

 

 

 

 

 

indicates the setting screen.

 

 

 

 

 

 

 

 

 

If the countdown start time is not displayed, use the

 

 

 

 

 

 

 

procedure under “To use the countdown timer” to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

display it.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Press C to move the flashing in the sequence shown
Auto-

repeat

 

On/Off status

below, and select the setting you want to change.

on indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Start Time

 

 

Start Time

 

 

Auto-Repeat

 

 

 

 

 

 

 

 

 

(Hours)

 

 

(Minutes)

 

 

On/Off

 

3.Perform the following operations, depending on which setting currently is selected on the display.

While the start time setting is flashing, use D (+) and B (–) to change it.Set 0:00 to specify 24 hours.

While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press D to toggle auto-repeat on (0N) and off (0F).

4.Press A to exit the setting screen.

The auto-repeat on indicator () is displayed on the Countdown Timer Mode screen while this function is turned on.

Frequent use of auto-repeat and the alarm can run down battery power.

Alarms

you turn the alarm off or change it to a one-time alarm.

Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode time.

Note

Pressing any button stops the alarm tone operation.

Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen Displaying the Alarm1 setting screen

To test the alarmIn the Alarm Mode, hold down D to sound the alarm.To select the operation of Alarm11.In the Alarm Mode, use D to select Alarm1.2.Press A to cycle through the available settings in the sequence shown below.

Module 4380

 

 

Module 4380

 

 

 

Module 4396

 

 

 

 

Module 4396

 

 

 

 

 

 

 

 

 

 

 

Module 5048

 

 

 

 

Module 5048

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

One-time alarm on

 

 

Snooze alarm on

 

 

Alarm off

The applicable alarm on indicator is displayed in all modes when an alarm is turned on.

The snooze indicator flashes during the 5-minute intervals between alarms.

Displaying the Alarm1 setting screen while the snooze alarm is turned on turns off the snooze alarm automatically (making Alarm1 a one-time alarm).

To turn Alarms 2 and 3 on and off
Alarm on indicator

Alarm on indicator

Alarm on indicator

Module 4380

Module 4396

Module 5048

Alarm date (Month – Day)

Alarm number

Alarm time (Hour : Minutes)

You can set up to three independent multi-function alarms with hour, minutes, month, and day. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. One of the alarms can be configured as a snooze alarm or a one-time alarm, while the other two are one-time alarms.

You also can turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.

There are three alarm screens numbered 1 through 3. The hourly time signal screen is indicated by :00.

All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.

1.In the Alarm Mode, use D to select a one-time alarm (alarm number 2 or 3).2.Press A to toggle the displayed alarm on and off.

Turning on a one-time alarm (2 or 3) displays the alarm on indicator on its screen.

The alarm on indicator is displayed in all modes.

If any alarm is on, the alarm on indicator is shown on the display in all modes.

To turn the hourly time signal on and off
Alarm Types
The alarm type is determined by the settings you make, as described below.Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to sound everyday at the time you set.

Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes the alarm to sound at the specific time, on the specific date you set.

1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

Hourly time signal on indicator

Hourly time signal on indicator

Hourly time signal on indicator

Module 4380

Module 4396

Module 5048

1.In the Alarm Mode, use D to select the Hourly Time Signal.2.Press A to toggle the displayed item on and off.

Turning on the Hourly Time Signal displays the hourly time signal on indicator on its screen.

The hourly time signal on indicator is displayed in all modes.

Dual Time

alarm to sound everyday at time you set, only during the month you set.Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm to sound every month at the time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm screens until the one whose time you want to set is displayed.

x1 x2 x3 :00
You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
and 3 can be used as one-time alarms only.
The snooze alarm repeats every five minutes.

Timekeeping Mode time

Dual time(Hour : Minutes Seconds)

The Dual Time Mode lets you keep track of time in a different time zone. You can select Standard Time or Daylight Saving Time for the Dual Time.

The seconds count of the Dual Time is synchronized with the seconds count of the Timekeeping Mode.

To set the Dual Time1.Press C to enter the Dual Time Mode.

2.In the Dual Time Mode, hold down A until the DST setting starts to flash, which indicates the setting screen.

3.Press C to move the flashing in the sequence shown below to select the other setttings.

DST Hour Minutes

2.

After you select an alarm, hold down A until the hour setting of the alarm time

 

starts to flash. This indicates the setting screen.

 

This operation turns on the alarm automatically.

3.

Press C to move the flashing in the sequence shown below to select other settings.

Hour Minutes Month Day

4.When the setting you want to change is flashing, use B and D to change it as described below.

Screen:

To do this:

Do this:

 

 

 

Toggle between Daylight Saving

Press D.

 

 

 

Time (ON) and Standard Time (OF)

 

 

 

 

 

 

 

 

Change the hour or minutes

Use D (+) and B (–).

 

 

 

 

 

5. Press A to exit the setting screen.

The DST indicator on the Dual Time Mode screen indicates that DST is turned on for the Dual Time Mode time.

3