Operation Guide DQD-106

USING THE ALARM

The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm Mode selector (2) to select the snooze alarm feature.

Setting the Alarm Time

Use the Alarm Time Set buttons (3) to set the alarm time.

Pressing the Alarm Time Set buttons (3) causes the alarm time to appear in place of the time on the display.

Press to change the

Press to change the

alarm time setting (+).

alarm time setting (—).

•Holding down + or – changes the digits at high speed.

Turning the Alarm On and Off

Use the Alarm Mode selector (2) on the side of the clock to turn the alarm on and off, and to select the snooze feature.

Alarm Mode selector

 

Description

 

 

 

 

SNZ

The alarm sounds at the preset time for one minute, and seven

 

more times every five minutes thereafter. Even if you stop the

(

)

alarm sound by pressing the SNOOZE/LIGHT button (1), the

alarm operation is performed again five minutes later.

 

 

 

 

• The indicator

flashes on the display to indicate that the

 

 

snooze feature is activated.

ALM ON

 

 

(

)

The alarm sounds at the preset time for one minute.

 

 

 

 

ALM OFF

The alarm does not sound.

 

 

 

 

•The light also turns on for the first five seconds that the alarm sounds.

•The alarm sound changes over four levels as it sounds.

Stopping the Alarm

•When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on, the alarm will sound again in about five minutes.

•To turn off the snooze feature, slide the Alarm Mode selector (2) to ALM OFF.

USING THE LIGHT

Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark.

Important!

•Overuse of the light can shorten battery life.

THERMOMETER FUNCTIONS

A built-in sensor measures temperature and shows the measured value on the display. The readout from the temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).

Temperature Measurements

•The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above 70°C (158°F).

•Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such readings are actually outside the guaranteed temperature range of this clock.

Switching between Celsius and Fahrenheit

•Push the °C/°F button (6) to select either Celsius (°C) or Fahrenheit (°F).

Celsius (°C)

Fahrenheit (°F)

°C/°F button (6)

°C/°F button (6)

°C

°F

BATTERY REPLACEMENT

Replace batteries whenever the display of the clock becomes dim and difficult to read.

1.Open the battery compartment cover as shown in the illustration.

2.Remove all of the old batteries.

3.Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If you load batteries incorrectly, they can burst and damage the clock.

4.Replace the battery compartment cover.

5.Press the RESET button (7). Be sure to press the RESET button (7) after replacing batteries.

Battery precautions

•Keep batteries out of the reach of small children. If a battery is swallowed accidentally, contact your physician immediately.

•Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.

•Never mix old and new batteries, or batteries of different brands.

•Never charge the batteries that come with the clock.

•Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your skin.

•Replace the batteries at least once a year, even if the current batteries are working properly.

•The batteries that come with the clock lose some of their power during transport and storage.

3