
Operation Guide 3403
World Time
World Time lets you display the current time in any one of 100 cities (35 time zones) around the world.
To view the times in other time zones
●1 In the Timekeeping Mode, press C to enter the World Time Mode.
Current date in | See “Using Modes” (page | |
World Time city | ||
|
1[WT100] will appear on the display for about
one second, and then the name of the currently selected World Time city will scroll across the display.
Current time in
City name | World Time city |
| |
|
Note
Scrolling of the World Time city name will stop after about two minutes. To restart scrolling, press A.
●2 Use B and D to scroll through the World Time Mode city names.
See “City Name List” (back of this manual).
ξScrolling to a city name displays the current time in that city.
ξHolding down either button scrolls at high speed.
ξTo display the UTC city name (UTC offset 0), press B and D at the same time.
●3 To return to the Timekeeping Mode, press C four times.
To configure the Summer Time (DST) setting
●In the World Time Mode, hold down A for about two seconds.
ξ[DST Hold] will appear on the display. After that,
[DST Hold] will disappear and the summer time setting will toggle to either on or off.
ξ DST on the display indicates that summer time is turned on.
DST indicator
Note
ξSummer time, or Daylight Saving Time (DST) as it is known in some countries, calls for setting clocks ahead one hour from standard time during the summer season. Note that the period during which and the areas where summer time is applied depend on each country. Some countries or geographic areas may not use summer time.
ξThe DST indicator will be on the display and timekeeping will be advanced by one hour when summer time is turned on.
ξThe summer time setting cannot be changed for the UTC World Time zone.
ξThe summer time setting is applied to the currently selected time zone only. A setting confi gured for one time zone does not affect any other time zone.
Alarms and Hourly Time Signal
Alarm setting screen | Hourly time signal setting screen |
You can set up to fi ve different alarms. When any one of the alarm times is reached the watch will sound an alarm tone and fl ash its display illumination, or it will vibrate for about 10 seconds. The hourly time signal causes the watch to sound a tone and
flash its display illumination or to vibrate every hour on the hour. See “To change the alarm/timer alert method” (page
To enter the Alarm Mode
●In the Timekeeping Mode, press C twice to enter the Alarm Mode. See “Using Modes” (page
[ALARM] will appear on the display for about one second. After that, an alarm setting screen (Alarm 1 through Alarm 5, or hourly time signal) will appear.
Alarm number | Current time |
Current time |
|
Note
If you do not perform any operation for about two or three minutes while in the Alarm Mode, the watch will automatically return to the Timekeeping Mode.
To change an alarm setting
●In the Alarm Mode, use D to select the alarm whose setting you want to change.
Alarm 1 |
| D |
| Alarm 2 |
| D |
| Alarm 3 | ||||
|
|
|
|
|
| |||||||
( |
| ) |
|
| ( | ) |
|
| ( | ) | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
D |
|
|
|
|
|
|
|
|
|
|
| D |
|
|
|
|
|
|
|
|
|
| |||
Hourly Time |
|
|
| Snooze alarm |
|
|
| Alarm 4 | ||||
Signal ( | ) |
| D |
| ( | ) |
| D |
| ( | ) | |
|
|
|
|
|
|
|
|
|
|
|
●Use B to select the alarm type or to toggle the hourly time signal between on and off.
Alarm 1 to 4
: Alarm does not sound.
: Alarmthat. sounds only once at the preset time and does not sound again after
: Alarm sounds at the preset time each day.
Snooze alarm
: Alarm does not sound.
: Alarm sounds at the preset time each day, and up to seven times at fi ve- minute intervals thereafter.
|
|
Hourly time signal
:Hourly time signal does not sound.
:Hourly time signal sounds every hour on the hour.
The Alarm indicator is displayed while an alarm is turned on, while the Hourly time signal indicator is displayed while the hourly time signal is turned on. When the snooze alarm is turned on, both the alarm indicator and the snooze indicator are displayed.
| Alarm on | Hourly time signal on |
Snooze indicator | Alarm indicator | Hourly time signal indicator |
●To change an alarm time setting, hold down A for about two seconds until the hour digits of the current alarm time start to flash.
[SET Hold] will appear on the display. After that, [SET Hold] will disappear and the hour digits will fl ash.
●4 Each press of C causes the flashing to move between the hour and the minutes digits.
The fl ashing digits are the ones that are selected.
●5 Use B and D to change the flashing setting, and set the hour and minutes you want.
ξHolding down either button scrolls the setting at high speed.
ξIf you are using