Auto-repeat indicator

USER’S GUIDE 2684

Stopwatch

To select the alarm type

1. In the Alarm Mode, press Dto display the alarm

Alarm on indicator

screen.

 

 

 

2. Press Ato cycle through the available alarm settings

 

shown below.

 

 

 

Alarm off

Single

Snooze

 

 

alarm on

alarm on

Snooze alarm on indicator The alarm on indicator and the snooze alarm on indicator are shown on the display in all modes while these functions are turned on.

1/100 second

Hours Seconds

Minutes

The stopwatch lets you measure elapsed time, split times, and two finishes.

The display range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds.

The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.

The stopwatch measurement operation continues even if you exit the Stopwatch Mode.

Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.

All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.

The snooze alarm on indicator flashes during the 5-minute intervals between alarms.

Displaying the Alarm Mode setting screen automatically changes the alarm type to single alarm.

Changing the Timekeeping Mode setting screen during a 5-minute interval between snooze alarms stops the current snooze alarm operation (but snooze alarm remains as the alarm type setting).

If a snooze alarm time is reached while you are setting the current time in the Timekeeping Mode, the alarm sounds only once. Subsequent snooze alarm operations are not performed.

Stopping a Snooze Alarm Operation

After a snooze alarm time is reached, you can perform the following steps during any 5-minute interval between alarms to stop the snooze alarm operation.

To stop a Snooze Alarm Operation

1.While in the Alarm Mode, press D to display the alarm screen.

2.Next, press Ato turn off the alarm or to select the single alarm.

Note that this also changes the alarm type setting. If you want to use the snooze alarm again, you must re-select it as the alarm type. See “To select the alarm type” for more information.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn the Hourly Time Signal on and off

1.In the Alarm Mode, press Dto display the Hourly Time Signal screen.

2.Press Ato turn it on and off.

Indicates Hourly Time Signal is on.

Indicates Hourly Time Signal is off.

The Hourly Time Signal on indicator is shown on the display in all modes while this function is turned on.

Countdown Timer

Hours Minutes

The countdown timer can be set within a range of

one minute to 24 hours. An alarm sounds when the

 

 

 

 

countdown reaches zero.

 

 

 

 

You can also select auto-repeat, which automatically

 

 

 

 

restarts the countdown from the original value you set

 

 

 

 

whenever zero is reached.

 

 

 

 

Countdown timer functions are available in the

 

 

 

 

Countdown Timer Mode, which you enter by pressing

 

 

 

 

C.

 

 

 

 

To use the countdown timer

 

Seconds

 

Press Dwhile in the Countdown Timer Mode to start the

 

 

 

 

 

 

 

 

countdown timer.

When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops.

The countdown timer measurement operation continues even if you exit the Countdown Timer Mode.

Press D while a countdown operation is in progress to pause it. Press Dagain to resume the countdown.

To completely stop a countdown operation, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value.

To set the countdown start time

1.In the Countdown Timer Mode, hold down Auntil the hours setting of the countdown start time starts to flash, which indicates the setting screen.

2.Press Cto move the flashing between the hours and minutes settings.

3.While a setting is flashing, use Dto increase it.

To set the starting value of the countdown time to 24 hours, set 0:00.

4.Press Ato exit the setting screen.

To turn auto-repeat on and off

1.In the Countdown Timer Mode, hold down Auntil the hours setting of the countdown start time starts to flash, which indicates the setting screen.

2. Press Bto toggle auto-repeat on (

displayed) and

off (

not displayed).

 

Note that pressing Bin the above operation also turns on the backlight.

3.Press Ato exit the setting screen.

When the end of the countdown is reached while auto-repeat is on, the alarm sounds, but the countdown restarts from the beginning without stopping. You can stop the countdown by pressing Dand manually reset to the start time by pressing A.

The auto-repeat indicator appears in the Countdown Timer Mode only.

To measure times with the stopwatchElapsed time
StartStopRe-start

Stop

Clear
Split time

 

 

 

 

Start

SplitSplit release

Stop

Clear

 

(SPL displayed)

 

 

 

Two Finishes

 

 

 

 

Start

Split

Stop

Split release

Clear

 

First runner

Second runner

Display time of

 

 

finishes.

finishes.

second runner.

 

 

Display time of

 

 

 

 

first runner.

 

 

 

Dual Time

The Dual Time Mode lets you keep track of time in a different time zone.

In the Dual Time Mode, the seconds count is synchronized with the seconds count of the Timekeeping Mode.

To set the Dual Time

1. Press Cto enter the Dual Time Mode.

Hour : Minutes

2. In the Dual Time Mode, hold down Auntil the hour

 

 

setting starts to flash, which indicates the setting

 

 

screen.

 

 

3. Press Cto move the flashing between the hour and

 

 

 

 

minutes settings.

 

 

4. While a setting is flashing, use Dto increase it.

 

 

5. Press Ato exit the setting screen.

Seconds

Reference

This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch.

Auto return features

If you leave a screen with flashing digits for two or three minutes without performing any operation, the watch automatically saves any settings you have made up to that point and exits the setting screen.

Scrolling

The D button is used to scroll through setting screen data on the display. Holding down this button during a scroll operation scrolls through the data at high speed.

Backlight Precautions

The backlight uses an LED (light-emitting diode) and a light guide panel that cause the entire display to glow for easy reading in the dark.

In any mode, press Bto illuminate the display for about one second.

The illumination provided by the backlight may be hard to see when viewed under direct sunlight.

The backlight automatically stops illuminating whenever an alarm sounds.

Frequent use of the backlight shortens the battery life.

2