Operation Guide 5001
Alarms
| Alarm number | You can set five independent Daily Alarms. When an |
| |||
| alarm is turned on, the alarm tone sounds when the alarm | |||||
Alarm time |
| time is reached. |
|
| ||
(Hour : Minutes) |
| You can turn on an Hourly Time Signal that causes the | ||||
|
|
|
| watch to beep twice every hour on the hour. |
| |
|
|
|
| • There are six screens in the Alarm Mode. Five are for | ||
|
|
|
| alarms (indicated by numbers from | through | ), |
|
|
|
| and one is for the Hourly Time Signal (indicated by |
| |
|
|
|
| ). |
|
|
|
|
|
| • All of the operations in this section are performed in the | ||
|
|
|
| Alarm Mode, which you enter by pressing C. |
| |
On/Off status |
| |||||
• You can select any one of three alarm beeper patterns. |
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is displayed.
•To set an alarm, display one of the screens indicated by an alarm number from through .
2.After you select an alarm, hold down Auntil the hour setting of the alarm time starts to flash, which indicates the setting screen.
•This operation turns on the alarm automatically.
3.Press Cto move the flashing between the hour and minute settings.
4.While a setting is flashing, use D(+) and B
•When setting the alarm time using the
5.Press Ato exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the watch is in.
•To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
•The alarm will sound using the currently selected beeper pattern.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press Ato toggle it on (ON displayed) and off
|
|
|
| (OF displayed). |
|
|
|
|
|
| • Turning on an alarm ( | through | ) displays the |
|
|
|
| alarm on indicator on its Alarm Mode screen. | ||
|
|
|
| • In all modes besides the Alarm Mode, the alarm on | ||
|
|
|
| indicator is shown for any alarm that is currently turned | ||
|
| On/Off status | on. |
|
| |
Alarm on indicator | • The alarm on indicator flashes while the alarm is | |||||
|
|
|
| sounding. |
|
|
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use Dto select the Hourly Time
Signal ().
2. Press Ato toggle it on (ON displayed) and off (OF displayed).
• Turning on the Hourly Time Signal displays the Hourly Time Signal indicator on its Alarm Mode screen.
•While the Hourly Time Signal is turned on, the Hourly
Time Signal on indicator is shown on the display in all modes besides the Alarm Mode.
Stopwatch
Countdown Timer
Hours | You can set the countdown timer within a range of | ||
one minute to 24 hours. An alarm sounds when the | |||
| Minutes | countdown reaches zero. | |
|
|
| • You can also select |
|
|
| |
|
|
| countdown automatically from the original value you set |
|
|
| whenever zero is reached. |
|
|
| • All of the operations is this section are performed in the |
|
|
| Countdown Timer Mode, which you can enter using C. |
Seconds
To use the countdown timer
Press Dwhile in the Countdown Timer Mode to start the countdown timer.
•When the end of the countdown is reached and
•When
•The countdown timer measurement operation continues even if you exit the Countdown Timer Mode.
•Press D while a countdown operation is in progress to pause it. Press Dagain to resume the countdown.
•To stop a countdown operation completely, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value.
To configure countdown timer settings
1. While the countdown start time is on the display in the Countdown Timer Mode, hold down Auntil the hour setting of the countdown start time starts to flash, which indicates the setting screen.
• If the countdown start time is not displayed, use the procedure under “To use the countdown timer” to display it.
2.Press Cto move the flashing in the sequence shown below to select other settings.
Hours Minutes
3.While a setting is flashing, use D and B to change it as described below.
Screen | To do this: | Do this: |
|
|
|
0:00 | Change the hours or minutes | Use D(+) and |
| Toggle | Press D. |
|
|
|
• To specify a countdown start time of 24 hours, set 0:00.
4.Press Ato exit the setting screen.
•The
•Frequent use of
Edit Mode
You can use the Edit Mode to configure the following settings, or to return the settings to their initial factory defaults.
•Button operation tone on/off
•Alarm beeper pattern
•
•
•Analog hand setting
•The analog hand setting will not change when you reset settings to their initial factory defaults.
•All of the operations in this section are performed in the Edit Mode, which you enter by pressing C.
•Each press of Dcycles through available settings in the sequence shown below.
Minutes
Seconds
1/100 second
The stopwatch lets you measure elapsed time, split times, and two finishes.
•The display range of the stopwatch is 59 minutes, 59.99 seconds.
•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.
•Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.
•All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.
| Press . |
|
|
|
|
|
| |||||
Button Operation |
|
|
|
| Alarm Beeper |
|
|
| ||||
Tone ( | ) |
|
|
|
| Pattern ( | ) |
|
| Timekeeping ( | ) | |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
Analog Hand Setting |
|
|
|
|
|
|
| |||||
( | ) |
|
|
|
|
|
|
| ( | ) |
|
Button Operation Tone
The button operation tone sounds any time you press one of the watch’s buttons. You can turn the button operation tone on or off as desired.
To measure times with the stopwatch |
|
| |||
Elapsed Time |
|
|
|
|
|
Start | Stop |
|
| Stop | Clear |
Split Time |
|
|
|
|
|
Start | Split |
| Split release | Stop | Clear |
| ( | displayed) |
|
|
|
Two Finishes |
|
|
|
|
|
Start | Split |
| Stop | Split release | Clear |
| First runner | Second runner | Display time of |
| |
| finishes. | finishes. | second runner. |
| |
| Display time of |
|
|
| |
| first runner. |
|
|
|
•Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer Mode alarm all operate normally.
To turn the button operation tone on and off
1. In the Edit Mode, use Dto display the Button
On/Off statusOperation Tone selection screen.
2. Press Ato toggle the button operation tone on (ON) and off (OF).
2