Casio 3150, MO0805-EA Rally Mode, lll, Special Stage Elapsed Time Measurement, Before Starting Measurement, Special Stage Timing, llll, Remaining Target Time Alert

Special stage elapsed time (hours, minutes, seconds, 1/10- second)

Operation Guide 3150

Rally Mode

The Rally Mode of your watch can be used to measure special stage elapsed time, and to keep track of the goal target time (countdown). The Rally Mode timing operation is shown in the illustration below.

Elapsed time 1/10-second indicator

Remaining		llll	l ll
		l	l
			l
target time		l l	l l
		lll	lll
		l	l
(hours:minutes)	ll	l
	lll
		l
Start point	l	l
	l l
		ll
Special stage (competitive section 42' 30" 0)
	Target time (0:50)

DStart

lll l l l l l l							Remaining target time
							(minutes, seconds)
l				l
ll					l
l						l
			ll l l			l
l		ll			l		l		l
			l
	l l		ll		l		l ll		l ll
	lll					l	l	l	l	l
	l l		l				l		l
	lll				l		l	l	l	l
				l l ll			ll		ll
Special stage time
measurement end										Goal

Road section (non-competitive 07' 30" 0)

DStop	The watch returns to the reset
BRecord elapsed time	screen automatically when the
	target time becomes zero.

Special Stage Elapsed Time Measurement

The special stage elapsed time is measured up to 99 hours, 59 minutes, 59.9 seconds. If the time exceeds this, timing reverts to zero and continues from there.

Before Starting Measurement

Special Stage Timing

Measured elapsed time

lll l l l				l l l
l				l
ll					l
					l
l				ll l l	l
l	lll
			l		ll
	lll	l	l

This section describes operations you can perform while special stage timing is in progress.

To pause the current time on the display

While a special stage timing operation is in

LT-05

LT-05 target time (0:50)

The watch comes with 10 preset target times (link times), which you can use as-is or change to the value you want.

You can use the B button to select the target time you want while the current target time is

reset to its initial value.
LT-01	0:10	LT-07	1:30
LT-02	0:20	LT-08	2:00
LT-03	0:30	LT-09	3:00
LT-04	0:40	LT-10	5:00
LT-05	0:50	OFF
LT-06	1:00

l	l	l	l
ll	l		l
		l
			l l ll

Target time

progress press the D button.

•This will pause the current elapsed time (flashing) on the display for about one or two minutes. Though the time is frozen on the display, the watch continues the special stage timing operation (and count down of the remaining target time) internally.

•While a time is paused on the display, you can record it in memory or reset the timing operation to zero. If you don’t do anything, the display will return to the normal elapsed time measurement screen after a few minutes.

To change a target time

		l	lll		1. While the current target time is reset to its
				l	initial value in the Rally Mode, hold down A
		l		l
		l
	l			l
			ll		until the display contents start to flash. This is
lll		l	llll
					the setting screen.
l				l	2. Use the D (+) and B(–) buttons to select
l
l	ll l l			l
				l	the target (link) time you want to change.

3. Press the C button so the current target time’s hour digit starts to flash.4. Use the D(+) and B(–) buttons to change the hour digit value.5. Press the C button to move the flashing to the minute digits.6. Use the D(+) and B(–) buttons to change the minute digit value.

7. After the time is setting you want, press the A button to exit the setting screen.

You can set a target time up to 24 hours, in units of one minute.

Target (link) time	C	Target time hours	C	Target time
number				minutes

C

To start a Rally Mode time measurement

To record the time paused on the display

While a time is paused on the display (see above), press the B button.

•This will save the paused time in memory and display the ongoing special stage timing operation.

•The watch has enough memory to store up to 30 time records. If there are already 30 records in memory, storing a new measurement time causes the oldest record to be deleted automatically to make room for the new one.

To reset the timing operation to zero

While a time is paused on the display (see above), hold down the B button.•This will reset the elapsed time operation to zero.

The watch has enough memory to store up to 30 measurement time records. If there are already 30 records in memory, storing a new measurement time causes the oldest record to be deleted automatically to make room for the new one.

To cancel an ongoing elapsed time measurement operation

Hold down the B button to reset the elapsed time operation to zero.

To change screen contents during elapsed time measurement

Press the B button to display the remaining target time. Note that this

Auto start countdown seconds indicator

Remaining auto start countdown time (36 seconds indicated here)

Press the D button to start the auto start countdown.

Time measurement (special stage) will start when the auto start countdown reaches 00 seconds.

•The watch will beep and display illumination will flash whenever the remaining auto countdown time reaches 50, 40, 30, 20, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1 and 0 seconds.

•You can cancel the auto start countdown at any point and start time measurement (special stage) manually by pressing the D button.

•You can cancel the countdown and return to the countdown start screen by pressing the B button while a countdown is in progress.

operation is not available if “OFF” is selected for the target time.

When the remaining target		When the remaining target
time is 5 minutes or more		time is less than 5 minutes
		l		ll
Target time		l ll		l	l
		l	l	l		l
		l		l
		l	l	l	l
		ll		ll			Target time
lll
ll	l
l	l
l l
	ll

Remaining Target Time Alert

The watch will beep and display illumination will flash when the remaining target time reaches the following points, 5, 3 and 1 minute, and 30, 10, 5, 4, 3, 2, and 1 second before time up, and at time up.

4