Operation Guide 3173 3246
Mode Reference Guide
Your watch has 10 “modes”. The mode you should select depends on what you want to do.
To do this: | Enter this mode: |
• View the current date in the Home City |
|
• Configure Home City and daylight saving time (DST) settings | Timekeeping Mode |
• Configure time and date settings |
|
|
|
View the sunrise and sunset times for a specific date | Sunrise/Sunset Mode |
•Determine your current bearing or the direction from your current location to a
destination as a direction indicator and angle value | Digital Compass Mode |
• View the barometric pressure and temperature at your current location | Barometer/Thermometer |
• View a graph of barometric pressure readings | Mode |
•The illustration below shows which buttons you need to press to navigate between modes.
•For about one second after you enter a mode by pressing D, a pointer will appear on the display pointing the applicable mode name on the watch's bezel.
•In any mode, press L to illuminate the display.Timekeeping ModeWorld Time |
| Data Recall |
| Sunrise/Sunset |
Mode |
| Mode |
| Mode |
|
|
|
|
|
|
|
| Countdown |
|
|
Stopwatch Mode |
|
| Alarm Mode | ||
| Timer Mode |
| |||
|
|
|
|
|
|
The functions and operations described in this section can be used in all of the modes.
Auto Return FeaturesTo do this: | Enter this mode: | |
• View the altitude at your current location |
| |
• Determine the altitude differential between two locations (reference point and | Altimeter Mode | |
current location) | ||
| ||
• Record an altitude reading with the measurement time and date |
| |
|
| |
Recall records created in the Altimeter Mode | Data Recall Mode | |
|
| |
View the current time in one of 48 cities (31 time zones) around the globe | World Time Mode | |
Use the stopwatch to measure elapsed time | Stopwatch Mode | |
Use the countdown timer | Countdown Timer Mode | |
|
| |
Set an alarm time | Alarm Mode | |
|
|
•You can use buttons A, B, and C to enter a sensor mode directly from the Timekeeping Mode or from another sensor mode. To enter a sensor mode from the Sunrise/Sunset Mode, Data Recall, World Time, Stopwatch, Countdown Timer, or Alarm Mode, first enter the Timekeeping Mode and then press the applicable button.
Sensor ModesDigital Compass Mode |
| Barometer/ |
| Altimeter Mode | ||||
| Thermometer Mode |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting either standard time or daylight saving time (DST).
•The watch returns to the Timekeeping Mode automatically if you do not perform any button operation for two or three minutes in the Sunrise/Sunset, Data Recall, Alarm, or Digital Compass Mode.
•If you leave a screen with flashing digits on the display for two or three minutes without performing any operation, the watch exits the setting screen automatically.
Initial ScreensWhen you enter the World Time, Alarm, or Digital Compass Mode, the data you were viewing when you last exited the mode appears first.
ScrollingThe A and C buttons are used on the setting screen to scroll through data on the display. In most cases, holding down these buttons during a scroll operation scrolls through the data at high speed.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.•Pressing E while in the Timekeeping Mode will cycle through the Timekeeping Mode display formats as shown below.
Day of the Week Screen | Year Screen | Barometric Pressure | |||
PM | Day of | Month |
|
| Graph Screen |
|
| Barometric | |||
indicator | week | Day | Year | ||
|
|
| pressure graph | ||
|
|
|
|
|
|
PM | City | Month | |
indicator | code | Day | |
|
|
|
|
|
|
|
|
1.In the Timekeeping Mode, hold down E until the currently selected city code starts to flash. This is the city code setting screen.
•Before the city code starts to flash, the message SET Hold will appear on the display. Keep E depressed until SET Hold disappears and the city code starts to flash.
•The watch will exit the setting mode automatically if you do not perform any operation for about two or three minutes.
•For details about city codes, see the “City Code Table”.2.Press A (East) and C (West) to select the city code you want to use as your Home City.
•Keep pressing A or C until the city code you want to select as your Home City appears on the display.
3.Press D to display the DST setting screen.4.Use A to toggle the DST settings between OFF and On.•Note that you cannot switch between standard time and daylight saving time (DST) while UTC is selected as your Home City.
5.After all the settings are the way you want, press E twice to return to the Timekeeping Mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.Note•After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate the current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the
DST indicator | 1. In the Timekeeping Mode, hold down E until the currently selected | |
city code starts to flash. This is the city code setting screen. | ||
|
will appear on the display. Keep E depressed until SET Hold disappears and the city code starts to flash.
2. Press D to display the DST setting screen.3. Use A to toggle the DST settings between OFF and On.4. After all the settings are the way you want, press E twice to return to the Timekeeping Mode.
•The DST indicator appears to indicate that Daylight Saving Time is turned on.2