Operation Guide 3271
• A graphic animation plays on the display while a stopwatch timing operation is being |
performed. You can toggle the animation on and off by holding down A while the |
Recall Mode
stopwatch is reset to all zeros. |
More than 10 hours
•Whenever the elapsed time exceeds 10 hours, the measurement changes from
Creation date (Month – Day)
Log number
Time measurement was performed
Log Title Screen
Use the Recall Mode to recall and delete records stored by the Stopwatch Mode.
•Stopwatch records are stored in “logs” that are created automatically by the watch. See “Memory Management” on page
•The title screen of the newest log appears first whenever you enter the Recall Mode.
•Log numbers are automatically assigned in sequence, starting from 01.
•All of the operations in this section are performed in the Recall Mode, which you enter by pressing C (page
To recall stopwatch records
In the Recall Mode, use A to scroll through the log title screens, starting from the newest one, as shown below. When the title screen of the log you want is displayed, use D (+) and B
|
|
| Stopwatch Record | Best Lap Time |
|
|
| Screen | Screen |
|
|
| Lap/Split number | BEST indicator |
|
|
|
| |
Log Title Screen |
| Lap time |
| |
|
|
|
| |
A |
| D |
| D |
| ▲ |
| ▲ | |
▲ | ▲ | ▲ | ||
|
| B |
| B |
A | ▲ |
| Split time | ▲ |
▲ |
|
| D |
|
B
•The locations of the lap time and split time in the Stopwatch Record screen are determined by the display format you last selected in the Stopwatch Mode (page
•The BEST indicator identifies the record that contains the best lap time in the log.
•If a best lap time record is deleted automatically when the log becomes full, the BEST indicator will not be transferred to the record with the next best lap time. See “Memory Management” on page
To delete a log
1.In the Recall Mode, display the title screen or one of the records of the log you want to delete.
2.While holding down B, hold down D for about two seconds until the watch beeps.
• “CLR” will flash on the display for two seconds and then the watch will beep.
Release B and D at this time.
• You cannot delete the log of an ongoing elapsed time measurement operation.
To delete all logs
1. While holding down B, hold down D for about five seconds until the watch beeps
Countdown Timer
once and then a second time.
•“CLR” will flash on the display for two seconds and then the watch will beep once. Keep B and D depressed and “ALL” will flash on the display for three seconds, and then the watch will beep again. This indicates that all log data is cleared.
•You cannot delete logs while an elapsed timing operation is in progress.
Number of Repeats
Seconds
Minutes | Timer 1 |
Dual timers can be set with two different starting times. The watch can be configured so the two timers alternate, so when one reaches the end of its countdown, the other timer starts. You can specify a “number of repeats” value, which controls how many times the
You can specify up to 10 repeats. The watch emits a short beep whenever either of the timers reaches the end of its countdown during an ongoing timer operation. The watch emits a
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The beeper stops after about 5 seconds or when you press any button.
|
|
To configure the countdown timer
1. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the current countdown start time starts to flash, which indicates the setting screen.
• If the countdown start time is not displayed, use the procedure under “To use the countdown timer” (page
2.Press C to move the flashing in the sequence shown below to select other settings.
Timer 1 |
|
| Timer 1 |
|
| Timer 2 |
|
| Timer 2 |
Minutes |
|
| Seconds |
|
| Minutes |
|
| Seconds |
Number of Repeats
3.When the setting you want to change is flashing, use D and B to change it as described below.
Setting | Screen | Button Operation |
Minutes, Seconds |
| Use D (+) and B |
|
|
|
Number of Repeats |
| Use D (+) and B |
|
|
|
• To disable either timer, set 00'00" as its countdown start time.
4.Press A to exit the setting screen.
|
|
To use the countdown timer
World Time
Current repeat count | Preset number of repeats | |
| (Reset) | |
Current timer time | Timer 1 or 2 | |
Current time | ||
(Start/Stop) | ||
|
Press D while in the Countdown Timer Mode to start the countdown timer.
•The countdown is performed by alternating between Timer 1 and Timer 2. A short beep is emitted to signal a changeover from one timer to the other.
•Press D to pause a countdown. Press D again to resume.
•Pressing B while a countdown timer is stopped resets it to the start time specified by you.
•The watch emits a
•Even if you exit the Countdown Timer Mode, the countdown timer operation continues and the watch beeps as required.
City code
Current time in selected city
World Time shows the current time in 48 cities (31 time zones) around the world.
•The times kept in the World Time Mode are synchronized with the time being kept in the Timekeeping Mode. If you feel that there is an error in any World Time Mode time, check to make sure you have the correct city selected as your Home City. Also check to make sure that the current time as shown in the Timekeeping Mode is correct.
•Select a city code in the World Time Mode to display the current time in any particular time zone around the globe. See the “City Code Table” at the back of this manual for information about the UTC differential settings that are supported.
•All of the operations in this section are performed in the World Time Mode, which you enter by pressing C (page