![Operating the computer [Measuring screen]](/images/new-backgrounds/27826/278263x1.webp)
Operating the computer [Measuring screen]
Tm Elapsed Time |
| Pace arrow |
| ||
| Indicates whether the current | |
0:00’00” - 9:59’59” |
| speed is faster ( ) or slower ( ) |
|
| than the average speed. |
C Cadence |
| Current speed |
| ||
0(20) - 299 rpm |
| 0.0(4.0) - 200.0 km |
|
| [0.0(3.0) - 125.0 mph] |
CC-RD200
Troubleshooting
MODE does not work when the computer is mounted on its bracket.
Check that there is no dirt between the bracket and the computer.
Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly.
Speed (Cadence) are not displayed. (Touch a metal item against two contact points of | The contacts to be short- |
the computer several times to create a short circuit while observing the display. If a | circuited intermittently are |
numeric value appears, this signifies that the computer is functioning normally.) | located on the back. |
Is the clearance between the sensor and magnet too great? (must be ≤ 3 mm) |
|
Does the magnet pass through the sensor line? |
|
Adjust the positions of the magnet and sensor. |
|
|
|
|
| Dst Trip Distance |
|
|
|
| 0.00 - 999.99 km [mile] |
|
|
|
| Dst 2 Trip |
|
|
|
| 0.00 - 999.99 / |
|
|
|
| 1000.0 - 9999.9 km [mile] |
MODE | Av Average Speed*2 | |||
*1 |
|
| 0.0 - 200.0 km/h | |
|
|
|
| [0.0 - 125.0 mph] |
|
|
|
| Mx Maximum Speed |
|
|
|
| 0.0(4.0) - 200.0 km/h |
|
|
|
| [0.0(3.0) - 125.0 mph] |
|
|
|
| Odo Total Distance |
|
|
|
| 0.0 - 9999.9 / |
|
|
|
| 10000 - 99999 km [mile] |
|
|
|
| Clock |
|
|
|
| 0:00 - 23:59 |
|
|
|
| or 1:00 - 12:59 |
*1 | With the computer installed on the bracket, | |||
|
| press on the three raised dots on the face of | ||
|
| the computer. |
| |
*2 | If Tm exceeds approximately 27 hours or | |||
|
| DST exceeds 999.99 km, .E (Error) is | ||
|
| displayed as the average speed. Reset data. | ||
Selected Mode
Starting/Stopping measurement
Measurements occur automatically when the bicycle is in use. During
measurement, or flashes.
Switching computer function
Pressing MODE switches function, in order, as shown on the left.
Resetting data
To reset measurement data, display any data other than for
The total distance is never reset.
Power-saving function
If the computer has not received any signal for an hour, power- saving mode will activate and only the clock will be displayed.
Alternatively, if the sensor detects a signal or MODE is pressed, the main display reappears.
Speed Cadence
Is there any foreign matter (which would prevent a clean contact) on the contact points of the computer and/or bracket?
Clean the contact points.
Check that no wire cable is worn or broken. Even with a normal appearance, it may be that a wire cable could be broken internally. Replace the bracket sensor set.
No display.
Is battery in the computer run down?
Replace it. Then reinitialize the computer referring to “Preparing the computer”.
Incorrect data appear.
Reinitialize the computer referring to “Preparing the computer”.
Specification
Battery | Lithium battery (CR1620) x 1 |
Battery life | Approx. 2 years (Using the battery one hour a day; the battery life will vary with the |
| conditions of use.) |
Controller | |
Display | Liquid crystal display |
Sensor | No contact magnetic sensor |
Wheel circumference range | 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm) |
Working temperature | 32 °F - 104 °F (0 °C - 40 °C) (This product will not function appropriately when exceeding the |
| Working Temperature range. Slow response or black LCD at lower or higher temperature |
| may happen respectively.) |
Dimensions/weight |
*The
*The specifications and design are subject to change without notice.
|
| Standard Parts |
|
Parts kit | Braket band | Braket/Sensor | Cadence magnet |
Changing the computer settings [menu screen]
To bring up the menu screen, press MENU in any mode. Each time MODE is 
pressed, the relevant menu screen appears. Pressing and holding MODE MENU changes the setting of the displayed menu.
MODE
MODE |
| MODE | MODE | MODE |
| |
Wheel | Wheel size entry | Clock setting | Total distance | Speed unit | ||
selection |
|
|
|
| manual entry |
|
| Setting |
|
|
|
|
|
| change (by | * | After changing, be sure to press MENU to register the setting. | |||
| * If the menu screen is not touched for a minute, the Measuring | |||||
| pressing & | |||||
MODE |
| screen reappears without data changes. |
| |||
| holding) |
|
|
|
|
|
|
|
|
|
|
| |
Wheel selection ..... Toggle between the specified wheel size (tire circumference)
and | . Use this function if the computer is to be shared | ||
between two bicycles. | and | . | |
Pressing MODE toggles between | |||
Wheel size entry .... Pressing MODE increases the value, and pressing and
holding MODE moves to the next digit.
*To enter the wheel size 
, display 
using “Wheel selection”. Clock setting .......... To set the clock, refer to “Preparing the
Total distance manual entry
................................ Before reinitializing the computer, note the total distance. This
| reading will later allow you to enter the total distance | ||
| manually. Pressing MODE increases the value, and pressing | ||
| and holding MODE moves to the next digit. |
| |
Speed unit | Pressing MODE toggles between | and | . |
Maintenance
To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.
Replacing the battery
If the display appears faded, replace the battery. |
|
|
Install a new lithium battery (CR1620) with the (+) | Close |
|
side facing upward. Then reinitialize the computer |
|
|
referring to “Preparing the computer”. | Open | CR1620 |
|
|
Lithium battery | ||
Wheel magnet | ||
(CR1620) | ||
|
LIMITED WARRANTY
(Accessories/Bracket sensor and Battery Consumption excluded)
CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer.
To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certificate.
Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.
For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.
CO.,LTD.
Service & Research Address for USA CATEYE Service and Research Center
1705 14th St. 115 Boulder, CO 80302 Phone: 303.443.4595
Toll Free: 800.5CATEYE
Fax: 303.473.0006
URL: http://www.cateye.com
