Planning
Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener.
Depending on your requirements, there are several installation steps which may call for materials or hardware not included in the carton.
ïInstallation Step 1 ñ Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural supports.
ïInstallation Step 5 ñ Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware may be required.
ïInstallation Step 10 ñ Depending upon garage construction, extension brackets or wood blocks may be needed to install sensors.
ïInstallation Step 10 ñ Alternate floor mounting of the safety reversing sensor will require hardware not provided.
ïDo you have an access door in addition to the garage door? If not, Model 1702LM Outside Quick Release is required. See Accessories page.
ïLook at the garage door where it meets the floor. Any gap between the floor and the bottom of the door must not exceed 1/4" (6 mm). Otherwise, the safety reversal system may not work properly. See Adjustment Step 3. Floor or door should be repaired.
SECTIONAL DOOR INSTALLATIONS
ïDo you have a steel, aluminum, fiberglass or glass panel door? If so, horizontal and vertical reinforce- ment is required (Installation Step 11).
ïThe opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of the header bracket, it may be installed within 4 feet (1.22 m) to the left or right of the door center. See Installation Steps 1 and 11.
ïIf your door is more than 7 feet (2.13 m) high, see rail extension kits listed on Accessories page.
SECTIONAL DOOR INSTALLATION |
| FINISHED CEILING |
|
| ||||
|
|
|
|
|
| |||
|
|
|
|
| Support bracket & |
| ||
|
|
|
|
| fastening hardware |
| ||
|
|
|
|
| is required. |
|
| |
Horizontal and vertical reinforcement | Slack in chain tension | See page 17. |
| |||||
is needed for lightweight garage doors |
|
|
|
| ||||
is normal when |
|
|
|
| ||||
(fiberglass, steel, aluminum, door with |
|
|
|
| ||||
garage door is closed |
|
|
|
| ||||
glass panels, etc.). See page 24 for details. |
|
|
|
| ||||
|
|
|
|
|
| |||
| Header Wall |
|
|
|
|
| Motor unit | |
|
|
|
| Extension |
|
|
|
|
|
|
| Torsion OR | Spring |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Spring |
|
|
|
|
|
|
|
| Wall- |
|
|
|
|
|
|
|
| mounted Access |
|
|
|
| |
|
|
| Door | Door |
|
|
|
|
|
|
| Control |
|
|
|
| |
| — |
|
|
|
|
|
| |
| Vertical |
|
|
|
|
|
| |
| — |
|
|
|
|
| CLOSED POSITION | |
| Centerline of |
|
| Header |
|
| ||
| — |
|
|
|
| |||
| Garage Door |
|
|
| Chain Pulley |
| ||
|
|
|
| Bracket |
| |||
|
|
|
|
| Bracket | Trolley | ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
| — — — |
|
|
|
| Garage |
| |
|
|
|
|
|
| Door |
| |
| — — |
|
|
|
| Spring |
| |
|
|
|
|
|
| Straight |
| |
|
|
|
|
|
|
| Emergency | |
|
|
| Safety |
|
|
| Door | |
|
|
|
|
|
| Arm | Release | |
| Gap between floor | Reversing |
|
|
|
| Rope & Handle | |
Safety Reversing Sensor | and bottom of door must | Sensor |
|
|
| Curved |
| |
not exceed 1/4" (6 mm) |
|
|
|
| Door |
| ||
|
| Header |
|
|
| |||
|
|
|
|
|
| Arm |
| |
|
|
|
| Wall | Door Bracket |
| ||
|
|
|
| Garage |
| |||
|
|
|
|
|
|
|
| |
|
|
|
| Door |
|
|
|
|
4