Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 1345C 1/3HP, 1355C 1/2HP Planning, ONE-PIECEDOOR WITH TRACK, SECTIONAL DOOR INSTALLATION, ONE-PIECEDOOR WITHOUT TRACK

1 72

Download 72 pages, 3.21 Mb

Planning

Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener.

SECTIONAL DOOR INSTALLATION

FINISHED CEILING

Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 19 for details.

Header Wall

Slack in chain tension is normal when garage door is closed

Support bracket & fastening hardware is required.

See page 12.

Motor unit

Torsion OR Spring

Wall-

Extension Spring

— —	Vertical
—	Centerline of
	Garage Door
— — —
— —

mounted Access

Door Door Control

	Gap between floor	Safety
	Gap between floor	Reversing
	and bottom of door	Sensor
Safety Reversing Sensor	must not exceed 1/4" (6 mm)

ONE-PIECE DOOR WITHOUT TRACK

FINISHED CEILING

Support bracket & fastening hardware is required. See page 12.

Slack in chain tension is normal when garage door is closed.

Header

Wall

Wall-mounted

Door Control

Access

Door

Motor Unit

ONE-PIECE DOOR WITH TRACK

Slack in chain tension is normal when garage door is closed.

	Gap between floor	Safety Reversing
	Gap between floor	Sensor
	and bottom of door	Sensor
	and bottom of door
	Safety Reversing must not exceed 1/4" (6 mm)
	Sensor

Safety

Reversing Sensor

Gap between floor and bottom of door must not exceed 1/4"

Access

Door

Safety Reversing Sensor

(6 mm).

4

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing your garage door Tools needed Planning Carton Inventory Attach the Rail to the Motor Unit IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY SENSORS ALIGNING THE SAFETY SENSORS TROUBLESHOOTING THE SAFETY SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY Repeat the safety reverse test (Adjustment Step 3, page 25) after any adjustment of limits or force HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 1702LMC Outside Quick Release: 335LMC Remote Light Control: LIFTMASTER SERVICE IS ON CALL HOW TO ORDER REPAIR PARTS LIFTMASTER ONE YEAR LIMITED WARRANTY Pour résidences seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planification Inventaire de la boîte d’emballage MONTAGE - 1re OPÉRATION Fixation du rail au moteur MONTAGE - 2e OPÉRATION Montage de la chaîne au pignon et installation du carter du pignon MONTAGE - 3e OPÉRATION IMPORTANTES INSTRUCTIONS CONCERNANT LA POSE Pour réduire le risque de BLESSURES GRAVES ou MORTELLES : POSE – 1re OPÉRATION Déterminer l’emplacement du support de linteau POSE – 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l’ouvre-porte POSE - 5e OPÉRATION Accrochage de l’ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose de l’ampoule et du diffuseur POSE - 8e OPÉRATION Pose de la corde et de la poignée de déclenchement d’urgence POSE - 9e OPÉRATION Exigences électriques POSE - 10e OPÉRATION Pose du Système Protector® Page Page POSE - 11e OPÉRATION Fixation du Support de Porte Page POSE - 12e OPÉRATION Fixation de la biellette au chariot Page RÉGLAGES - 1re OPÉRATION Réglage des courses d’ouverture et de fermeture RÉGLAGES - 2e OPÉRATION Réglage de la force RÉGLAGES - 3e OPÉRATION Essai du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Système Protector® FONCTIONNEMENT IMPORTANTES CONSIGNES DE SÉCURITÉ ou DE MORT : Utilisation de votre ouvre-portede garage Utilisation de la commande de porte à montage mural Ouverture manuelle de la porte ENTRETIEN DE L’OUVRE-PORTEDE GARAGE DÉFAUTS DE FONCTIONNEMENT 1 ÉCLAIR 2 ÉCLAIRS 3 ÉCLAIRS 4 ÉCLAIRS 5 ÉCLAIRS PROGRAMMATION Pour ajouter ou reprogrammer une télécommande à main supplémentaire Pour effacer tous les codes de la mémoire du moteur * Télécommandes à trois boutons Pour ajouter, reprogrammer ou modifier un NIP d’entrée sans clé PIÈCES DE RECHANGE Pièces d’assemblage du rail Pièces pour la pose Pièces d’assemblage du moteur ACCESSOIRES SERVICE À VOTRE DISPOSITION COMMENT COMMANDER DES PIÈCES DE RECHANGE GARANTIE LIMITÉE DE UN AN DE LIFTMASTER