Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 2585 3/4 HP Rail Assembly Parts, Installation Parts, NO, NO, NO, NO, KEY, KEY, PART, PART, DESCRIPTION, DESCRIPTION, REPAIR PARTS

1 36

Download 36 pages, 2.9 Mb

REPAIR PARTS

Rail Assembly Parts	6

3

1

		4	7
2		4
2
		5
		KEY	PART
		NO.	NO.	DESCRIPTION
		1	4A1008	Master link kit
		2	41B5424	Belt pulley bracket
	8	3	41B3869-1	Complete trolley assembly
	8	4	109B33	Trolley clip
		4	109B33	Trolley clip
		5	2777BD	One-piece T-rail
		6	41A5434-11	Full belt assembly
		7	41B4103	Tensioner assembly
		8	83A11-2	Rail grease

Installation Parts

4

					2
				1	3
				1
LO
CK	LIG
	LIG
		HT
					6
			5		7
			5
N
O
TIC					10
	E

			8		9
					9
		LY
	NT	ON
	OU
	G M
	LIN
	CEI
	UP

12

11

KEY	PART
NO.	NO.	DESCRIPTION
1	98LM	Motion detecting door control panel
2	973LM	3-button remote control
3	10A20	3V2032 Lithium battery

429B137 Remote control visor clip

541A2828 Emergency Release rope & handle assy.

641B4494-1 2-Conductor bell wire, white & white/red

741A5047-1 Door bracket w clevis pin & fastener

841A4353-1 Header bracket w/clevis pin & fastener

941A5034 Safety sensor kit (receiving and sending eyes) with 3' (.9 m)

2-conductor bell wire

10178B34 Straight door arm section

11178B35 Curved door arm section

1241A5266-1 Safety sensor brackets (2)

NOT SHOWN

41A2770-5 Installation hardware bag (includes hardware listed on page 5)

114A2735 Owner’s manual 114A2735SP Owner’s manual - Spanish

33

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing your garage door Tools needed Planning Carton Inventory Attach the Rail to the Motor Unit Set the Belt Tension Attach the Belt Cap Retainer Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY SENSORS ALIGNING THE SAFETY SENSORS TROUBLESHOOTING THE SAFETY SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: ïOpen door adjustment: decrease UP travel limit ïClosed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY Repeat the safety reverse test (Adjustment Step 3, page 25) after any adjustment of limits or force HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 1702LM Outside Quick Release: 2778BD 8 Foot (2.4 m) Complete Rail: 2770BD LIFTMASTER GARAGE DOOR OPENER FIVE-YEARLIMITED WARRANTY LIFETIME MOTOR AND BELT LIMITED WARRANTY