MODEL 33LM 3-BUTTON REMOTE CONTROL

OWNER’S MANUAL

The green push button is recommended for use with a garage door opener. The other push buttons can be used to operate another opener and/or light control product.

The 33LM 3-Button Remote Control Remote control can also be used with a 423LM 3-channel receiver and a 3-button door control to operate a commercial door opener in open, close, and stop mode (as explained on side 2).

To match or change the code in the remote control

Locate the code switches in both the new and the original remote controls. The new remote control’s code switches can be found by sliding the battery compartment cover back. Place remote controls side by side as shown (Figure 1) and set switches in all remote controls to matching positions (+,0,–). Use a pen or screwdriver to slide the code switches.

Figure 1

–

0

+

–

0

+

1

 

 

1

 

 

2

 

 

2

 

 

3

 

 

3

 

 

4

 

 

4

 

 

5

 

 

5

 

 

6

 

 

6

 

 

7

 

 

7

 

 

8

 

 

8

 

 

9

 

 

9

 

 

Match code switches (2-9) between old remote control and new remote control (Code switch #1 on the 3-button remote control is dormant)

WARNING

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

•ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.

•Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Programming the opener

RED-1WHT-2

+

 

 

H

0

I

G

 

H

– 1 2 3 4 5 6 7 8 9

N O R M

O R

RED-1WHT-2

H

I

G

H

N O R M

If your unit has a “Learn” button:

1. Press and release the “learn” button

located on the back panel of the motor

NOTE: Code switch #1 on the 3-button remote control is dormant, when used with a single-button remote control. Set code switch #1, in the single-button remote control, to match the push button selected on the

3-button remote control (Figure 2).

Figure 2

(+) (0) (–)

Push Buttons

unit. The learn indicator light will glow

H

 

H

 

I

 

G

steadily for 30 seconds.

NOR

 

2. Within the 30 second window, press and hold the button on the hand-held remote.

3.The unit will either activate or the opener light bulb will blink signifying it has learned the code.

If your unit has code switches:

1. Using a step ladder climb up to the back

of your motor unit. Check the code

switch settings on the back of the motor

unit.

+

H

0I G

H

–

1 2 3 4 5 6 7 8 9

Replacement Parts

Remote case housing

(circuit board not included) . . . . . . . . . . . . . .41A3580-4

Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29C128

2. Use a pen or screw driver to set the

code switches on the back of the remote

control to match the code switches on

the back of the motor unit.

+

0

—

1 2 3 4 5 6 7 8 9

12V battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A14

3.Once the code switches have been set push the remote control button to activate your unit.

1