
PROGRAM A TEMPORARY PIN
NOTE: This feature is not available on garage door openers that have a green Learn button or an external receiver.
A temporary
? ? ? ? +
PIN
...the light bulb blinks 3 times.? ? ? ? +
Temporary PIN
The light bulb will blink 4 times.3
Press the numberof hours the+ temporary PINwill work (up to 255).NUMBER OF HOURS
Then press the * button.
| 3 | NUMBER OF OPENINGS |
OR | Press the number | Then press |
of openings the | ||
temporary PIN | + the # button. | |
| will work (up to 255). |
|
1 blink |
| 1 blink |
To test, press the temporary PIN, then press the ENTER button. The garage door opener will activate. If the temporary PIN was set for a number of openings, the test will use up one opening.
To clear the temporary PIN, repeat steps
INSTALLATION
1Select a location to mount the Keyless Entry at a minimum height of 5 feet (1.5 m) out of the reach of children.
2Remove battery cover and battery.3Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.4Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the Keyless Entry over the top screw.
5Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing.
6Reinstall battery and replace cover.OPERATION
The garage door opener activates when the PIN and ENTER button are pressed. The keypad will blink for 15 seconds, during that time the ENTER button can be used to stop, start or reverse the door.
If the wrong number is accidentally pressed, press the correct PIN then the ENTER button. The Keyless Entry will transmit only the last four digits that were pressed before the ENTER button.
ONE BUTTON CLOSE: The Keyless Entry has a feature that allows the door to be closed using the ENTER button instead of a PIN.
NOTE: This feature is not available on garage door openers manufactured prior to 2006 or an external receiver.
To deactivate the one button close feature:
1Press and hold the 1 and 9 buttons for 10 seconds.2The keypad will blink four times when the one button close feature is deactivated.
To activate the one button close feature:
1Press and hold the 1 and 9 buttons for 10 seconds.
2The keypad will blink twice when the one button close feature is activated.REPLACEMENT PARTS
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A25
Keypad Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D621
Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D541
BATTERY
WARNING
To prevent possible SERIOUS INJURY or DEATH:•NEVER allow small children near batteries.•If battery is swallowed, immediately notify doctor.Replace the battery when the keypad | 9V Battery |
becomes dim or does not light after a |
|
button is pressed. |
|
Dispose of old battery properly. |
|
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.
www.chamberlain-diy.com
| © 2011, The Chamberlain Group, Inc. |
114A3926 | All Rights Reserved |