OPERATION

Door Control Push Bar:

Press to open or close the door.

Press again to reverse the door during the closing cycle, or

to stop the door while it is opening.

Light Feature:

Press the Light button to switch the opener

light on or off. When the door is opened or closed, the light

will remain on for 4-1/2 minutes. Press the Light button to
turn it off sooner. The Light button will not control the
opener light when the door is in motion. When using the
opener lights as working lights, we recommend that you

first disable the motion sensor. See

Automatic Light

Override Feature,

below.

 

When used with openers manufactured after

December 1, 1999, (check the date on the opener panel)

the 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock button

until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to 1-1/2 minutes. Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

Automatic Light Feature:

The opener light will turn on

automatically when a person enters the garage. When a

 

person walks in front of the door control, the opener light
will come on for five minutes, then shut off. This feature
works by detecting body heat. It is more sensitive in front
of the door control than at its sides, and works better as a

person moves closer. It may not work in temperatures

 

around 100˚F.

 

 

To disable this feature, slide the Detector Switch on the

 

right side of the door control down (off).

 

 

Special note for older garage door openers:

If this door

control is installed on an opener manufactured from

 

January 1, 1995 to December 1, 1999, the following

 

difference may apply: If the light is on when the opener is

 

actuated, the light may go off for a moment, then turn on

 

again as the detector senses you.

 

 

Automatic Light Override Feature:

 

We recommend that

you disable the motion sensor when using the opener

 

lights as working lights. Otherwise, they will turn off

 

automatically if you are working beyond the sensor’s

 

range. Slide the Detector Switch on the right side of the

 

door control down (off), then press the light button to

 

control the lights.

 

 

Energy Saving Feature:This door control senses the brightness inside the garage, and will not turn the light on if

it is already bright enough. If the light sensor turns on the light when it is not needed or does not turn it on when it is dark, the sensitivity can be adjusted. Remove the push bar cover by gently prying off the top edge with a coin or screwdriver. Underneath there is a dial below the green light on the right side. Use a small screwdriver to turn the dial by 1/4 turns: counterclockwise to make the light come on, or clockwise to make the light go off. Replace the cover by inserting top tabs and snapping into place.

Lock Feature: Designed to prevent operation of the door from portable remote controls. However, the door will open and close from the Door Control push bar and from the

Keylock and Keyless Entry accessories.

To activate: Press and hold the Lock button for 2 seconds. The push button indicator light will flash as long as the lock

is on.

To turn off: Press and hold the Lock button again for 2 seconds. The indicator light will stop flashing. Normal operation will resume. The Lock feature will also turn off whenever the Smart button on the opener end panel is activated.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817

 

© 2000, The Chamberlain Group, Inc.

 

114A2396B

All Rights Reserved

Printed in China