Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain CSO 1/2HP Assembly Hardware , Installation Hardware, Safety Reversing Sensor Installation Hardware

1 36

Download 36 pages, 1.06 Mb

Lock Washer

5/16" (4)

Nut 5/16"-18 (6)

Clevis Pin

5/16"x2-3/4" (1)

NOTICE

Handle

Insulated

Staples (10)

Assembly Hardware Installation Hardware

Dry Wall Anchors (2)

Clevis Pin

5/16"x1" (2)

Hex Screw

5/16"-18x7/8" (4)

Rope

Nut

5/16"-18 (5)

Washered Screw

5/16"-18x1/2" (4)

(2 -mounted in opener)

Carriage Bolt

5/16"-18x2-1/2" (2)

Carriage Bolt

1/4"-20x1/2" (7)

Master Link (2)

Ring

Fastener (3)

Trolley Threaded Shaft (1)

Screw

6ABx1-1/2" (2)

Lock Washer 5/16" (6)

Lag Screw

5/16"-9x1-5/8" (4)

Lock Nut

1/4"-20 (4)

Carriage Bolt

1/4"-20x1/2" (4)

Safety Reversing SensorInstallation Hardware

Hex Screw

1/4-20x1-1/2" (2) Screw

#10-32x3/8" (4) Lock Nut

#10x32 (4)

Wing Nut (2)

Insulated

Staples (20)

RAIL GREASE

NO. 83A4

Rail Grease

Hex Screw

5/16"-18x7/8" (3)

Lag Screw

1/4x1-1/2" (4)

Lock Nut

1/4"-20 (7)

Hex Screw

1/4"-20x5/8" (2) Screw

#8-32x3/8" (1) Lock Washer

1/4" (2)

6

Group all hardware found in all packages contained in the rail and opener cartons intothe three kits illustrated below.

Contents

Main MODEL CSO 1/2HP COMMERCIAL STRENGTH OPERATOR For Residential and Light Duty Commercial Use Install on Sectional Doors Only OWNER'S MANUAL properly aligned. shown. Start by reviewing these important safety alert symbols serious injuries or death Mechanical Electrical Read the instructions carefully. WARNING CAUTIONCAUTION You'll Need Tools Before you begin, survey your garage area. Do any of the following conditions apply to you? 5 Carton Inventory NOTICE Assembly Hardware Installation Hardware Safety Reversing Sensor Installation Hardware Assembly Step 1 To avoid installation difficulties, do not run the garage door opener until instructed to do so. Right Wrong Assemble the Rail & Attach the Chain Pulley Bracket Assembly Section: Pages 7 10 Assembly Step 2 Install the Trolley on the Rail Remember to use only these screws! Assembly Step 3 Fasten the Rail to the Power Head Assembly Step 4 Attach the Chain & Rail Support Bracket To attach the rail support bracket: do not re-adjust the chain. ALWAYS IMPORTANT INST ALLATION INSTRUCTIONS To reduce the risk of severe injury or death to persons: An improperly balanced door may not reverse and could result in severe injury or death. Ropes connected to a garage door can cause entanglement and death. Installation Section: Pages 11 23 Installation Step 1 Determine Header Bracket Location The door might not reverse when required, and could cause Fasten the Header Bracket to the Wall Fasten the Header Bracket to the Ceiling Installation Step 2 Install the Header Bracket Installation Step 3 Attach the Rail to the Header Bracket Installation Step 4 Position the Opener Installation Step 5 Hang the Opener each The opener could fall and injure someone if it is not properly secured. Installation Step 6 Install the Door Control close open The garage door could close and cause Installation Step 7 Install the Light Installation Step 8 Attach the Manual Release Rope and Handle The rope knot could become untied and you could fall. Installation Step 9 Electrical Requirements and If permanent wiring is required by your local code, refer to the following procedure: NOT The Protector System Figure 1: Facing the door from inside the garage Information you'll need before you begin the installation of the safety reversing sensor. must Installation Step 10 Install the Safety Reversing Sensor (Receiving and Sending Eyes) For Wall For Door Track For Garage Wall or Door Track Figure 7 glow steadily Installation Step 11 Fasten Door Bracket & Plate Installation Step 12 Connect Door Arm to Trolley Hole Alignment Alternative above cut end down Adjustment Step 1 Adjust the UP and DOWN Limits down reverses up Adjustment Step 2 Adjust the Force up stops nuisance reversals Adjustment Step 4 Test the Safety Reverse System Adjustment Step 3 Test The Safety Reversing Sensor Important safety check IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death to persons: Failure to properly adjust the opener may result in severe injury or death. dim or off Maintenance Schedule Weak or broken springs may cause the door to fall rapidly, causing injury or death to persons. Operation of Your Opener Operation of the Door Control Button stop The garage door could close and cause A moving garage door could injure or kill someone under it. Receiver and Remote Control Programming Having a Problem? Situation Probable Cause & Solution Having a Problem? (continued) Situation Probable Cause & Solution Page Repair Parts Accessories Available for your Opener Required Index CHAMBERLAIN SERVICE IS ON CALL 1-800-528-9131 HOW TO ORDER REPAIR PARTS 1-800-528-9131