Chamberlain ML5500 manual Special Feature of the Motorlift 5500, Accessories

HAVING A PROBLEM? (Continued)

7. Opener noise is disturbing in living quarters of home:

If operational noise is a problem because of proximity of the opener to the living quarters, Vibration Isolator Kit 41A3263 can be installed. This kit was designed to eliminate the "sounding board effect" and is easy to install.

8. The garage door opens and closes by itself:

•Is there a neighbor with a garage door opener using the same frequency code? Change your code.

•Make sure remote push button is not stuck “on.”

9. Door stops but doesn't close completely:

Review Travel Limits Adjustment.

Repeat safety reverse test after any adjustment of door arm length, close force or down limit.

10. Door opens but won't close:

• Check The Protector System™ (if you have installed this accessory). If the light is blinking, correct alignment.

•If opener lights do not blink and it is a new installation, check the down force.

Repeat the safety reverse test after the adjustment is complete.

11. Opener light does not turn on:

Replace light bulb (40 Watts maximum, 230V, E27). Replace burned out bulbs with rough service light bulbs.

12. Opener light does not turn off:

There may be a defective earth at the ceiling or wall receptacle. The unit must be earthed.

13. Opener strains or maximum force is needed to activate door:

Door may be unbalanced or springs are broken. Close door and use manual release rope and handle to disconnect trolley. Open and close door manually. A properly balanced door will stay in any point of travel while being supported entirely by its springs. If it does not, call for professional garage door service to correct the problem. Do not increase the force to operate the opener.

14. Opener motor hums briefly, then won't work:

•Garage door springs are broken. SEE ABOVE.

•If problem occurs on first operation of opener, door may be locked.

Disable door lock.

15. Opener won't activate due to power failure:

•Pull manual release rope and handle straight down to disconnect trolley. Door can be opened and closed manually. When the power is restored, pull the manual release handle toward the opener at a 45˚ angle, so that the trolley release arm is horizontal. The next time the opener is activated, the trolley will reconnect.

•The Outside Quick Release accessory 1702EML (if fitted) disconnects the trolley from outside the garage in case of power failure.

SPECIAL FEATURE OF THE MOTORLIFT 5500 24

Door within a door connection

Remove cover. Locate auxiliary terminal block. Remove jumper from terminal leads 1 and 2 (not shown). Replace with magnetic contact switch leads as shown.

ACCESSORIES 25

(1)Model 4330EML Single-Function Remote Control

(2)Model 4333EML 3-Function Remote Control

(3)Model 4335EML 3-Function Mini Remote Control

(4)Model 845EML Multi-Function Door Control Panel

(5) Model 75EML Lighted Door Control Button

(6)Model 747EML Wireless Keyless Entry Keypad

(7) Model 760EML Outside Keylock

(8)Model 1702EML Outside Quick Release

(9)Model 770EML The Protector System™

(10) Model 1EML	Door Handle Quick Release
(11) Model 34EML	2-Position Key Switch Flush Mount
Model 41EML	2-Position Key Switch Surface Mount

(12)Model 1703EML The Chamberlain Arm™

WIRING INSTRUCTIONS FOR ACCESSORIES

Lighted Push Button:				Protector System™:
To opener terminals:				To opener terminals:
Red-1 and White-2				White-2 and Black-3
Outside Keylock:				Wall Control Panel:
To opener terminals:				To opener terminals:
Red-1 and White-2				Red-1 and White-2
REPLACEMENT PARTS		26	-	27
SPECIFICATIONS
Max. Pull Force	900N
Watts	510W
		Motor
Type	Permanent split capacitor
Speed	1500 rpm
Volts	230-240 Volts AC-50Hz Only
	Drive Mechanism
Reduction	1.27:1
Drive	Screw. 2 Lead worm. Aluminum rail.
Length of Travel	Adjustable to 2,23m (7.4 feet)
Travel Rate	152mm (6 inches) per second
Lamp	1x230V/40W/E27 socket, on when door starts,
	off 4-1/2 minutes after stop.
Door Linkage	Adjustable door arm. Pull cord trolley release.
	Safety
Personal	Push button and automatic reversal in down
	direction. Push button and automatic stop in up
	direction.
Electronic	Independent up and down force adjustment screws.
Electrical	Motor overload protector and low voltage push
	button wiring.
Limit Adjustment	Screwdriver adjustment on side panel.
Start Circuit	Low voltage push button circuit.
	Dimensions
Length (Overall)	3,1m (122 inches)
Headroom Required ....	6cm (2.3 inches)
Hanging Weight	19 kg (41.8 lb)
	Receiver Memory Registers
Computer Code	12
Code Switch	1
Keypad	1

114A2421D

6-GB