Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain PD752D, PD752KLD Hardware Inventory, ASSEMBLY HARDWARE, INSTALLATION HARDWARE

1 40

Download 40 pages, 4.14 Mb

Hardware Inventory

Separate all hardware and group as shown below for the assembly and installation procedures.

ASSEMBLY HARDWARE

Bolt 1/4"-20x1-3/4 (1)	Lock Washer	Nut
	3/8" (1)	3/8" (1)

Bolt 1/4"-20x2-1/2 (1)	Lock Nut
	1/4"-20 (2)

Master	Idler Bolt (1)
Link (2)

Trolley Threaded Shaft (1)

INSTALLATION HARDWARE

Carriage Bolt	Wing Nut	Ring	Spacer (2)	Nut 5/16"-18 (8)	Handle
1/4"-20x1/2" (2)	1/4"-20 (2)	Fastener (3)

Lag Screw	Hex Bolt		Insulated
5/16"-9x1-5/8" (2)	5/16"-18x7/8" (4)	Lock Washer 5/16" (7)	Staples (30)

Lag Screw	Screw	Screw 6-32x1" (2)	Rope
5/16"-18x1-7/8" (2)	6ABx1-1/4" (2)

Self-Threading Screw	Drywall Anchors (2)	Washer 5/8" (2)
1/4"-14x5/8" (2)

Clevis Pin	Clevis Pin	Clevis Pin	Spacer (2)
5/16"x1-1/2" (1)	5/16"x1" (1)	5/16"x1-1/4" (1)

Contents

For Residential Use Only Introduction Assembly Adjustment Operation Installation11-26 Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Chain/Cable Tighten the Chain Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY Repeat the safety reverse test (Adjustment Step 3, page 29) after any adjustment of limits or force HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953D 3-ButtonSECURITY✚® Remote Control: 956D LIFTMASTER® ONE YEAR LIMITED WARRANTY LIFETIME MOTOR LIMITED WARRANTY