Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain WD822KD 1/2 HP Rail Assembly Parts, Installation Parts, NO, NO, KEY, PART, KEY PART, DESCRIPTION, REPAIR PARTS, NO. NO. DESCRIPTION

1 40

Download 40 pages, 4.33 Mb

REPAIR PARTS

	Rail Assembly Parts
	1	2
	1	3
		3
	4	6
		6

5	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	4A1008	Master link kit
	2	41C5141-1	Complete trolley assembly
	3	41A5665-2	Complete rail
	4	41B4103	Spring trolley nut
7	5	144C54	Idler pulley
	6	41A5250	Full belt assembly
	7	41D598-1	“U” bracket
			NOT SHOWN
		183A163	Wear pads

Installation Parts

4

1	2
1
3
LOCK
LIGHT
6
5	7
	7
N
O
TIC
E
10	11

89

13

12

KEY PART

NO. NO. DESCRIPTION

141C494-1 Multi-Function door control panel

2	953D	3-Button remote control
3	10A20	3V2032 Lithium battery

429B137 Remote control visor clip

541A2828 Emergency release rope and handle assembly

641B4494-1 2-Conductor bell wire, white and white/red

741A5047-1 Door bracket w clevis pin & fastener

841A5047-3 Header bracket w/clevis pin & fastener

941A5034 Safety sensor kit (receiving and sending eyes) with 3' (.9 m) 2-conductor bell wire

10178B34 Straight door arm section

1112B776 Hanging brackets

12178B35 Curved door arm section

1341A5266-1 Safety sensor brackets (2)

NOT SHOWN

41A5257-3 Installation hardware bag (includes hardware listed on page 7)

114A3043 Owner's manual 114A3043SP Owner's manual - Spanish

37

Contents

For Residential Use Only Introduction Assembly Adjustment Operation Installation11-26 Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer Set the Tension Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY Repeat the safety reverse test (Adjustment Step 3, page 29) after any adjustment of limits or force HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES PROGRAMMING NOTICE: To Add or Reprogram a Hand-heldRemote Control USING THE “LEARN” BUTTON To Erase All Codes From Motor To Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PIN To set a temporary PIN hours times Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953D 3-ButtonSECURITY✚® Remote Control: 956D CHAMBERLAIN® ONE-YEARLIMITED WARRANTY 10 YEAR BELT LIMITED WARRANTY & LIFETIME MOTOR LIMITED WARRANTY