Channel Plus DMT-16 Modular connectors, Wiring a 110 connector, Wiring a telephone wall plate

Typical Installation

Included: (1) Expansion Jumper 24”. (2) Flat Surface Mounting Ears.

(1) Disconnect Jumper (66) Labels

	Wire Color Codes		Solid Color
		brown RING Twisted-Pair
	pair 4	TIP	Wire
		brown/white
		green RING	blue
Cat5	pair 3	green/white TIP	white pair 3
4 pair UTP		orange RING	yellow

Modular connectors

6 position connectors

	PR2	PR3
		PR2
PR1	PR1
		PR1
R T	T RT R	T T RT RR
1 2 3 4 5 6	1 2 3 4 5 6	1 2 3 4 5 6
RJ-11	RJ-14	RJ-25

Security system connection (RJ-31X)

Each line is individually surge protected to 50 Joules and 4000 Amps. Some surges contain

pair 2	TIP	black pair 2
orange/white
	RING	red

Single line	Dual line	Rare
telephones,	telephones &	3 line KSU

Install this jumper for normal operation. Remove to d i s c o n n e c t t e l e p h o n e service from the system.

Expansion Jumper

(included)

sufficient energy that although your system has been protected, the surge circuit will be unable to provide additional protection. When this happens, the red light for that line will turn on and the module needs to be returned for

service.

Active Line Indicators

pair 1	blue
	blue/white TIP green pair 1

Wiring a 110 connector

8 position connectors

PR2

PR3 PR1 PR4

TRT RT RT R

1 2 3 4 5 6 7 8

RJ-45 (wired to TIA T568A standard) Ethernet (both 10BaseT and 100BaseT) Structured wiring of phones and data lines

From	telephone
company 4 Lines
	®

4 Lines to 16 telephone wall plates.

Line Ringing

Keep sheath close to connector Untwist .5” max.

110 punch down tool

The 110 is a sophisticated

i n s u l a t i o n d i s p l a c e m e n t

connection system. To push the

wires between the contact blades, use only a 110 punch down tool. Using a screwdriver may not seat the wire properly and can damage the contacts.

Note order of colors

Wiring a telephone wall plate

Cable Color	Pin #	Connector Color
	Pin 1	N/C
White/Orange	Pin 2	White/Orange
Blue	Pin 3	Blue
White/Blue	Pin 4	White/Blue
Orange	Pin 5	Orange

Option: old style wall plate

Pairs 1 & 2

Telephone Distribution Module DMT-16

Back	Bedroom	Dining	Guest	Master	Office
Door	4	Room	House 2	Suite 2	3
Basement	Bedroom	Family	Guest	Master	Patio
	5	Room	Room	Suite 3
Bathroom	Bedroom	FAX	Guest	Master	Play
	6		Room 1	Suite 4	Room
Bathroom	Bedroom	FAX	Guest	Media	Pool	Example
1	7	2	Room 2	Center	House
						Front	Family
Bathroom	Children’s	Fitness	Hall	Media	PVR		Room
2	Room	Center		Center 1
Bathroom	Children’s	Front	Hall	Media	PVR
3	Room 1	Door	2	Center 2	1	Rear

		Pin 6 N/C
	Pairs 1 & 2
		RJ-14
Pairs 3 & 4		Voice Grade Jacks
Cable Color	Pin #	Connector Color
	Pin 1	N/C
White/Brown	Pin 2	White/Orange
Green	Pin 3	Blue
White/Green	Pin 4	White/Blue
Brown	Pin 5	Orange
	Pin 6	N/C

Yellow

Black

Red Green

Yellow

Black

Red Green

Pairs 3 & 4

Bat		Children’s	Game	Kitchen		Modem		Satellite
Phone		Room 2	Room
Bedroom		Children’s	Garage	Laundry		Modem		Satellite
		Room 3		Room		2		1
Bedroom		Children’s	Garage	Living		Office		Satellite
1		Room 4	2	Room				2
Bedroom		Den	Guest	Master		Office		Satellite
2			House	Suite		1		3
Bedroom		Den	Guest	Master		Office		Satellite
3	2		House 1	Suite 1	2		4

Wiring a Cat-5 jack

1

Keep sheath close to jack.

110 punch- down tool

2

3

Label Card: Separate and slide labels into extrusion, or flip the label over for a blank surface.

Follow color code for T568A jacks. Position first pair to channel closest to end of jack. (Do not untwist conductor pairs more than 0.5" from the termination point.)

Using a 110 punch-down tool, push wires into channels and trim.

Repeat for subsequent pairs.

When all conductor pairs are terminated, snap on strain relief caps.

2 3