Chromalox®
Installation, Operation
and
RENEWAL PARTS IDENTIFICATION
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIVISION 4 |
|
|
| SECTION RADD | |
SALES | (Supersedes |
| |||
REFERENCE | |||||
|
|
|
|
|
|
DATE DECEMBER, 2008
The Safety Alert Symbol ! is used to indicate a risk of per- sonal injury.
Please familiarize yourself with these instructions before attempting to install or operate this Radiant Heater.
Type RADD Electric
Radiant Heaters
B
A
Before Installing:
1.Open carton and remove heater at the place of installation. Mounting clamps are in parts bag in carton.
2.Check nameplate volt and watt rating against your power sup- ply voltage and heating requirements of your installation. This nameplate is located on one end of the heater.
Specifications
|
|
| A | B | |
Model No. | Volts | kW | Overall Length | Heated Length | |
120 or 240 | 1.6 | ||||
208 or 275 | |||||
|
|
| |||
120 or 240 | 2.2 | ||||
208 or 275 | |||||
|
|
| |||
208 or 275 | 2.6 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 3.6 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 4.3 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 5.0 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 5.4 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 6.0 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 6.7 | ||||
240 or 480 | |||||
|
|
| |||
208 or 275 | 7.2 | 78 | |||
240 or 480 | |||||
|
|
| |||
208 or 275 | 9.0 | 106 | |||
240 or 480 | |||||
|
|
| |||
240 or 480 | 8.0 | 106 | |||
240 or 480 | 10 | 141 | 132 | ||
240 or 480 | 11 | 150 | |||
240 or 480 | 13 | 174 |
The system designer is responsible for the safety of this equipment and should install adequate
INSTALLATION
ELECTRIC SHOCK HAZARD. Disconnect all power before installing or servicing heater. Failure to do so could result in personal injury or property dam- age. Heater must be installed or serviced by a qualified person in accordance with the National Electrical Code, NFPA 70.
1.These radiant heaters are designed for indoor installation only.
2.Mounting Clamps — Mount heaters by using the mounting clamp and 3/8” bolt assembly.
(Interlocking Connectors
Discontinued)
Clamp assembly may be attached to heater by sliding over end or by snapping over top of extruded frame section at any point along its length. (see Fig. 2) For proper heater support, the maximum distance between clamps must not exceed 48”. On
3.Mounting Holes — When heaters are mounted adjacent to each other in the same plane, note that distance between mounting holes on framing to support heaters will be
4.Framing — Where an extensive installation is being made, the use of continuous slot metal framing manufactured by several concerns will be of assistance in saving time and money. The framing is reusable.
Figure 1 — Heater Parts and Dimensions | Figure 2 |
|
© 2010 Chromalox, Inc.