APX480M manual.qxd 3/12/2004 1:07 PM Page 13

Operation/Installation Manual

FINAL SYSTEM CHECK

1.Start the engine and turn on the source unit. After a two-second delay, slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting. Depending on your system design, the levels may become quite loud even at low Volume Control settings. Until you get an “audio feel” of the system’s power, use care when adjusting controls.

2.Turn the Balance Controls to their extreme positions and listen to the results. Audio output should match control settings (audio from the left speaker when balance is left).

3.Increase the volume and verify that the amplifier reproduces audio (at full frequencies) without distortion. If you hear distortion, check the connections and verify that the Gain Control is set correctly. Another possibility is damaged speakers or under-powered speakers. Once again refer to Troubleshooting for additional help.

TROUBLESHOOTING

Problem

No Audio.

Solution

Low or no remote turn-on voltage. Check remote connections at amplifier and source unit.

Blown amplifier fuse. Replace with new fast-blow fuse (same rating).

Power wires not connected. Check battery and ground wiring at amplifier; also check battery connections.

Speaker leads shorted. Check speaker continuity to ground, it should not show a common ground.

Speakers not connected or are blown. Check speaker connections at amplifier, measure coil impedance.

Problem

Audio cycles on and off.

Solution

Thermal protection circuits are shutting amplifier off. Check location for adequate ventilation; consult an authorized Clarion Audio Dealer.

Problem

Distorted audio.

Solution

Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.)

11

Page 12 Page 14
Page 13
Image 13
Clarion APX480M manual Final System Check, Troubleshooting
Page 12 Page 14

APX480M specifications

The Clarion APX480M is a cutting-edge marine amplifier that combines power with durability, making it an excellent choice for boat enthusiasts who want to enhance their audio experience on the water. This amplifier is designed to deliver high-quality sound and can power even the most demanding marine audio systems.

One of the standout features of the APX480M is its impressive power output. With a maximum output of 480 watts, it can drive multiple speakers and subwoofers effectively, providing a rich sound experience. The amplifier operates at a 4-channel configuration, allowing for diverse installation options. It is capable of delivering 60 watts RMS per channel into 4-ohm loads, ensuring that you can achieve loud and clear audio without distortion, even at higher volumes.

The APX480M is built for the tough marine environment. It has been designed and constructed to resist moisture and corrosion. The amplifier features conformal coated circuit boards, which protect the electronics from harsh marine conditions such as saltwater and humidity, contributing to its longevity and reliability. Additionally, the rugged aluminum heatsink provides efficient thermal management, preventing overheating during extended use.

Another notable characteristic of the APX480M is its built-in high-pass and low-pass crossovers. These allow users to fine-tune their audio system, ensuring that each speaker receives the appropriate frequency range. This feature enhances overall sound quality and helps in achieving a balanced audio experience, essential for listening to music while cruising on the water.

The amplifier also incorporates advanced technologies for improved performance. Some of these technologies include a MOSFET power supply, which maximizes efficiency and minimizes signal loss, and a variable bass boost, allowing users to emphasize low frequencies for a more powerful bass response. It also features low-level RCA inputs, making it easier to connect to head units for seamless integration into existing audio systems.

Installation is made simple with the APX480M, thanks to its compact design and user-friendly layout. The amplifier comes with a comprehensive set of mounting options and a straightforward wiring scheme, making it accessible for both novice and experienced installers.

In summary, the Clarion APX480M stands out in the marine audio market with its powerful output, durable construction, and versatile features. Whether you are sailing on a serene lake or navigating rough seas, this amplifier ensures an unparalleled audio experience that can withstand the elements while delivering crisp, high-quality sound.
Top Page Image Contents