
Printed in Japan 1999/7(CL.K)
CCD Camera Power Supply Box
| Installation Instructions |
4. Mounting Procedure
1. Precautions
Mount the CCD camera power supply box in a location such as under a seat using either the supplied tapping screws (ø4 x 12) or velcro.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
2. Package Contents
■Mounting Using Tapping Screws
ø4✕12
CCD camera power supply box
ø 4✕12
■Mounting Using Velcro
CCD camera power supply box
Velcro
*Thoroughly wipe any dirt from the mounting surface.
*Remove the separator from the back of the velcro and apply it to the mounting surface.
1. CCD camera power supply box: ············· 1 | 4. Bag of accessories: ················· 1 bag | Fig.3 |
| Fig.4 | ||
| Clamp: ······················································ 1 |
|
| |||
2. Selector switch: ························ 1 bag |
|
| ||||
| Tapping screws: ········································ 4 |
|
| |||
AUTO/MANU selector switch: ··················· 1 |
|
|
|
|
| |
Mounting fitting: ········································5. Bag of accessories:1 | ················· 1 bag | ■ Mounting the Switch on the Dashboard |
| |||
Label: ························································Connectorcable (red): ······························1 1 |
|
| ||||
|
|
|
| Mount the switch on the dashboard as shown in Fig. 6 using the supplied switch mounting | ||
3. Bag of accessories: ················· 1 bag | Connector cable (light green): ·················· 1 hole (Fig. 5). |
|
| |||
| Connector cable (black): ··························· 1 |
|
| |||
Electro taps: ·············································· 2 |
|
| Prepared ø 12 hole | Cosmetic cover (vehicle part) | ||
| Connector cable (red): ······························ 1 |
|
| |||
Velcro: ······················································· 1 |
| Label |
| |||
Velcro: ······················································· 1 |
|
| ||||
|
|
| ||||
3. Making Connections |
|
|
| Cosmetic cover (vehicle part) |
|
|
|
|
|
|
|
| |
|
|
|
|
| AUTO/MANU selector | |
|
|
|
|
|
| |
| AUTO/MANU selector switch |
|
|
| switch cable | |
<1DIN TV, 2DIN TV> |
|
|
|
| Mounting nut |
|
|
|
|
|
|
| |
|
|
|
|
| Upper | CAUTION |
|
|
|
|
|
| |
| White |
|
|
|
| Selector switch knob |
| Yellow |
|
| Prepared ø 12 hole |
|
|
|
|
|
|
|
| |
| CCD camera | CCD camera |
|
|
| Mount so that notch on AUTO/MANU |
| power supply box |
|
|
|
| |
|
|
|
| Fig.5 |
| selector switch faces downward. |
|
|
|
|
|
|
| Light green |
| Black |
Red | To reverse gear |
| signal (12 V) |
| GND |
| To ACC power supply (12 V) |
Fig.6
■Mounting the Switch Below the Dashboard
Assemble the AUTO/MANU selector switch as shown in Fig. 7 and mount it below the dashboard. (See Fig. 8.)
For making connections to a TV or video monitor equipped with a video input jack
Fig.1
Hook up the supplied connector cables as shown in Fig. 2.
Light
Mounting fitting
Label
Nut
MANU
Mounting fitting |
|
|
A |
|
|
Label |
|
|
Harness |
|
|
| M |
|
Nut | AN | Clamp |
U | ||
AUTO/MANU selector switch | AUTO | Harness |
| ||
|
| AUTO/MANU selector switch |
Black
Red
green
To reverse gear signal (12 V)
GND
To ACC power supply (12 V)
Used to provide a 12 V power supply to an additional device.
Fig.2
AUTO
Clamp | Tapping screws (ø 4 x 12) |
|
*Secure the switch harness to portion Aof the mounting fitting using the clip.
Fig.7 | Fig.8 |
CAUTION
1. | If harnesses will come into contact with the sharp edges of metal plates, or the like, protect |
| them using grommets or insulation tubes. |
2. | Before drilling any holes in a vehicle, make sure that there are no electrical wires, brake fluid |
When connection cannot be made to the terminals, use the supplied Electro Tap to make the connection as illustrated in the diagram.
As illustrated in the diagram, the intermediate | ||
cable is brought against the stopper and bent | ||
back in the direction of the arrow. | ||
The tip of the cable is |
| |
cut at a convenient |
| |
length. | Not needed | |
From the vehicle side |
| |
Latch | From the unit | |
Coupler connected to | ||
another piece of |
| |
equipment | Stopper | |
Power cable | ||
|
From the unit
Pass the
Hook | Power cable |
Close with pliers until the latch engages.
pipes, or the like, running behind to surface to be drilled. |
3. When installation is complete, test the AUTO/MANU selector switch to make sure it works |
properly. |
Explanation of label indications
• MANU (manual) : The CCD camera image is given output priority.
•AUTO (automatic) : Normally, the TV image is output. The camera image is output when the transmission is shifted into reverse.
Clarion Co., Ltd.