Printed in Japan 2006/2(CL.K) 284-8050-01
CCD Camera Power Supply Box

CAA-188-210

Installation Instructions
1. Precautions

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

4. Mounting Procedure
4-1. Mounting the CCD Camera Power Supply Box

Mount the CCD camera power supply box in a location such as under a seat using either the supplied tapping screws (ø4 x 12) or velcro.

Mounting Using Tapping ScrewsMounting Using Velcro

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

ø412

CCD camera power supply box

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

INFORMATION FOR USERS:.

CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

2.Package Contents

1.CCD camera power supply box: ·············1 4. Bag of accessories: ················· 1 bag

2. Selector switch: ························ 1 bag
Clamp: ······················································ 1
Tapping screws: ········································ 4
AUTO/MANU selector switch: ··················· 1

 

Mounting fitting: ········································ 1
5. Bag of accessories: ················· 1 bag
Label: ························································ 1Connector cable (red): ······························ 1
3. Bag of accessories: ················· 1 bag
Connector cable (light green): ·················· 1
Connector cable (black): ··························· 1
Electro taps: ·············································· 2

Connector cable (red): ······························ 1

Velcro: ······················································· 1

 

Velcro: ······················································· 1

 

CCD camera power supply box

ø412

Velcro

* Thoroughly wipe any dirt from the mounting surface.

* Remove the separator from the back of the velcro and apply it to the mounting surface.

Fig.3Fig.4
4-2. Mounting the AUTO/MANU Selector Switch
Mounting the Switch on the Dashboard

Mount the switch on the dashboard as shown in Fig. 6 using the supplied switch mounting hole (Fig. 5).

Prepared ø12 hole

Cosmetic cover (vehicle part)

 

Label

 

Cosmetic cover (vehicle part)

3. Making Connections
3-1. System Connection Example

<1DIN TV, 2DIN TV>

 

Light green

 

Black

Red

To reverse gear

 

signal (12 V)

 

GND

 

To ACC power supply (12 V)

AUTO/MANU selector switch

White

 

Yellow

 

CCD camera

CCD camera

power supply box

 

AUTO/MANU selector switch cable

Mounting nut

 

Upper

CAUTION

 

 

 

 

Selector switch knob

Prepared ø12 hole

 

 

 

 

Mount so that notch on AUTO/MANU

Fig.5

 

selector switch faces downward.

 

 

 

 

Fig.6
Mounting the Switch Below the Dashboard

Assemble the AUTO/MANU selector switch as shown in Fig. 7 and mount it below the

Fig.1

For making connections to a TV or video monitor equipped with a video input jack

dashboard. (See Fig. 8.)

Mounting fitting

 

Label

Harness

Mounting fitting

3-2. Connecting the Supplied Cables
Hook up the supplied connector cables as shown in Fig. 2.

Nut

 

AUTO/MANU selector

 

 

 

MANU

switch

Label

Black

Red

Light green

AUTO

Clamp

* Secure the switch harness to portion A of the mounting fitting using the clip.

Nut

MANU

Clamp

 

 

 

AUTO

Harness

 

 

 

 

AUTO/MANU selector

 

 

switch

Tapping screws (ø4 x 12)

 

To reverse gear signal (12 V)

 

GND

 

To ACC power supply (12 V)

FIG.2

Used to provide a 12 V power supply

to an additional device.

Fig.7Fig.8
CAUTION

1.

If harnesses will come into contact with the sharp edges of metal plates, or the like, protect

 

them using grommets or insulation tubes.

2.

Before drilling any holes in a vehicle, make sure that there are no electrical wires, brake fluid

3-3. Power Cable Connections

When connection cannot be made to the terminals, use the supplied Electro Tap to make the connection as illustrated in the diagram.

pipes, or the like, running behind to surface to be drilled.

3. When installation is complete, test the AUTO/MANU selector switch to make sure it works

properly.

From the vehicle side Coupler connected to another piece of equipment

Power cable

From the unit

Hook Power cable

As illustrated in the diagram, the intermediate cable is brought against the stopper and bent back in the direction of the arrow.

The tip of the cable is

 

cut at a convenient

 

length.

Not needed

Latch

From the unit

Stopper

Pass the vehicle-side cable through and bend back in the direction of the arrow.

Vehicle-side wire

Explanation of label indications
• MANU (manual) : The CCD camera image is given output priority.

AUTO (automatic) : Normally, the TV image is output. The camera image is output when the transmission is shifted into reverse.

Close with pliers until the latch engages.

Unit-side cable

Clarion Co., Ltd.

Vehicle-side cable