HIGHLINETM TENT 12’ X 12’ MODEL 2000001091
Before you begin
Read all instructions before set up.
•Select a level campsite clear of rocks, branches, and other hard or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
•Do not set up your tent under trees.
•For best results in windy conditions, position end of tent into the wind.
•Enlist the help of at least one other person to assist you when it is time to assemble the tent.
Parts and Components
Description | Part Number |
Main Poles, Black (2) | 5010000433 |
Main Poles, Gray (2) | 5010000506 |
Vestibule Pole, Long, Thin, Black (1) | 5010000507 |
Rainfly Ridge Pole, Thin, Black w/ Metal Tips (1) | 5010000434 |
Rear Awning Pole (1) | 5010000508 |
Rainfly | 5010000435 |
To Set Up Tent
1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. (Fig. 1)
2. Assemble all poles by interlocking the
3. Insert gray main poles through the sleeves on both sides of tent; then insert black main poles through sleeves, in front and back of tent. Make sure black poles overlap the gray poles. (Fig. 1)
Black,longer, | Front & Back |
Main Poles | Sleeves |
Side Sleeve |
| Door |
| Side Sleeve | |
| Gray, Main Poles | ||||
|
|
| |||
|
| Fig. 1 | |||
|
|
|
|
| |
|
|
|
|
|
|
STITCH LINE
4.Insert end of each black & gray main pole into pins . (Fig. 2 & 2A)
5.Go to opposite end of each pole and gradually apply pressure to each forming arches. Insert the pin into each pole end at the sides and corners of tent. (Fig. 2 & 2A)
6.Attach frame clips along edges of tent to the black & gray main poles. (Fig. 2B)
7.Stretch tent until taut, then secure metal loops located on both sides and corners of tent with stakes. (Fig. 2C)
2B
Door
2A
Fig. 2 | 2C |
|
To Attach Rainfly
1.Insert rainfly ridge pole with metal tips through sleeve in underside of rainfly. (Fig. 3)
2.Drape rainfly over tent with rainfly ridge pole centered from above front door to back of tent & the green vestibule flaps located in the front. (Fig 4).
3.Insert rainfly ridge pole into metal grommet on front of tent, apply pressure until pole forms an arch, then insert other end into back grommet. (Fig. 4 & 4A). NOTE: Because of the position of the center grommets, it may be necessary to gently pull to
on the front & back arches for easier access.
4.Insert vestibule pole through sleeve in rainfly at front of tent. (Fig. 4)
5.Locate all hook & loop fasteners on underside of rainfly and wrap around black and gray poles to secure. (Fig. 5)
6.Stretch elastic straps and hook clip on each to the metal loops at the four corners of the tent. (Fig. 6)
|
|
|
|
|
|
|
| Sleeve in Rainfly |
|
|
|
| |
|
|
| Metal Tip | |||
| Rainfly |
|
| |||
| Thin, Black, | |||||
|
|
| Rainfly |
| ||
|
|
| Ridge Pole |
|
|
|
|
|
| Fig. 3 | |||
|
|
|
|
| ||
|
|
|
|
|
|
|
Fig. 4
4A |
| |
|
|
|
| Door | Vestibule |
|
| Pole |
Green Vestibule Flaps | Sleeve in | |
Rainfly | ||
|
|
|
|
|
|
(continued on other side) |
| Fig. 5 |
|
| Fig. 6 |
|
|
|
|
|
