Coleman 2000001595 manual To Set Up Tent, To Attach Rainfly, Before you begin, Pole Descriptions

WEATHERMASTER® 4 SCREENED TENT

Before you begin

Read all instructions before set up.

•Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines.

•Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.

•Secure with all stakes and guylines provided to prevent property damage or personal injury.

•For best results in windy conditions, position narrow end of tent into the wind.

•Enlist the help of at least one other person to assist you when it is time to assemble the tent.

Pole Descriptions

Description	Qty.	Pole	Pole	Pole
		Dia.	Repair Kit	Replacement Kit
Long Leg Pole, steel
(w/ red marking)	4	19mm	N/A	5010000621
Short Leg Pole, steel	4	19mm	N/A	5010000618
Curved Ridge Pole, steel
(w/ red marking)	2	19mm	N/A	5010000620
Curved Ridge Pole, steel	2	19mm	N/A	5010000619
Awning Pole,
black, fiberglass	1	6.3mm	5010000543	5010000545

To Set Up Tent

MODEL 2000001595

6.Rotate all eight Leg Poles upright and insert

pin on each web loop at the side locations	7A
as shown. (Fig. 7 & 7A)	Pin

Fig. 7

7. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8)

Fig. 8

STITCH LINE

1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)

Fig. 1

Door

2. Pull four corners of tent taut, then secure by driving stakes through web loops at an angle for better anchoring. (Fig. 2)

		Fig. 2
3. Assemble four, steel, shock-corded,
			Fig. 3
curved Ridge Poles. Insert Ridge Poles
	Ridge Poles
(with red marking) into center sleeves	with Red
	Marking
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
			Sleeves
into the other two sleeves on top of tent.			with Red
			Trim
4. Assemble eight, steel, shock-corded,

8.To stretch tent to finished size:

•Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.9);

•Pull up on top Leg Pole section until tent is taut;

•Twist the lower Leg Pole clock- wise until the button locks into the center or lowest hole;

•Repeat on remaining Leg Poles.

9.Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 10) NOTE: It may be necessary to remove metal stakes through web straps at side of tent and screen room, pull tent taut, and drive in stakes to secure.

Fig. 9

Upper

Leg Pole

Section

Button

Center Hole

Lower Hole

Lower

Leg Pole

Section

Fig. 10

Leg Poles. Push down on steel button
on tapered end and insert into end with
four holes.				Button in
NOTE: Make sure steel button locks into				third hole		Fig. 4
third hole on pole as shown. (Fig.4)
5. Insert curved end of
long Leg Poles (with red
			Ridge Poles with
marking) into the ends			Red Marking
of the Ridge Poles (with
red marking). Insert
curved end of remaining
						Sleeves
		Curved End of
short Leg Poles into the		Long Leg Pole				with Red
						Trim
	Fig. 5
ends of the remaining
Ridge Poles. (Fig. 5 & 6)
						Fig. 6
					Ridge Poles with
					Red Marking in
					center 2 sleeves

To Attach Rainfly

1.Drape Rainfly over tent. Make sure seams on Rainfly are facing down and centered over poles of the tent. (Fig. 11) NOTE: Hook and loop fasteners, located on seams of under - side of Rainfly, should be centered over Ridge Poles.

2.Assemble thin, black, shock-corded Awning Pole; then insert through sleeve in Rainfly above door. (Fig. 11)

Rainfly

Awning

Pole

Sleeve

Door

Fig. 11

(continued on other side)