![](/images/new-backgrounds/1246388/2463881x1.webp)
WEATHERMASTER® 8 TENT MODEL 2000001596
STITCH LINE
Before you begin
Read all instructions before set up.
•Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
•Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.
•Secure with all stakes and guylines provided to prevent property damage or personal injury.
•For best results in windy conditions, position narrow end of tent into the wind.
•Enlist the help of at least one other person to assist you when it is time to assemble the tent.
Pole Descriptions
Description | Qty. | Pole | Pole | Pole |
Dia. | Repair Kit | Replacement Kit | ||
Long Leg Pole, steel |
|
|
|
|
(w/ red marking) | 2 | 19mm | N/A | 5010000612 |
Short Leg Pole, steel | 4 | 19mm | N/A | 5010000622 |
Curved Ridge Pole, steel |
|
|
|
|
(w/ red marking) | 1 | 19mm | N/A | 5010000617 |
Curved Ridge Pole, steel | 2 | 19mm | N/A | 5010000616 |
Window Vent Pole, |
|
|
|
|
black, fiberglass | 2 | 8.5mm | 5010000541 | 5010000547 |
|
|
|
|
|
To Set Up Tent
1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)
Fig. 1
Door
2. Pull four corners of tent taut, then secure by driving stakes through web loops at an angle for better anchoring. (Fig. 2)
|
|
| Fig. 2 |
|
| |
3. Assemble three, steel, |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Fig. 3 | |
curved Ridge Poles. Insert Ridge Pole |
|
|
|
| ||
| Ridge Pole | |||||
|
|
|
| |||
(with red marking) into center sleeve |
| with Red |
|
| ||
| Marking |
|
| |||
on top of tent with the red trim (Fig. 3). |
|
|
|
|
|
|
Insert the remaining curved Ridge Poles |
|
|
|
|
| Sleeve |
6.Rotate all six Leg Poles upright and insert
pin on each web loop at the side locations | 7A | |
as shown. (Fig. 7 & 7A) |
| |
Pin | ||
|
7B |
Fig. 7 |
Metal Tip |
Sleeve | Hole in | |
Leg Pole | ||
|
Window Pole
7C
6.Assemble the two,
7.Insert tapered metal tip on Window Pole into Leg Pole. NOTE: It may be necessary to gently rotate Leg Pole so the hole will line up with the Window Pole.
8.Go to opposite end of each window pole and gradually apply
pressure to the pole forming an arch. Insert the pin into the leg pole end at the corners of tent. (Fig. 7 & 7C)
9. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8)
10. Locate web strap with plastic hook on
the sides of each end panel Window Vent, then snap onto
the corner Leg Pole. (Fig. 9)
into the other two sleeves on top of tent. |
| with Red | |||||||||
| Trim | ||||||||||
4. Assemble six, steel, |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||||
Leg Poles. Push down on steel button |
|
|
|
|
|
| |||||
on tapered end and insert into end |
|
|
|
| Button in third hole | ||||||
with four holes. |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| Fig. 4 | ||
NOTE: Make sure steel button locks |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||
into third hole on pole as shown. (Fig.4) |
|
|
| ||||||||
5. Insert curved end of Leg |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Poles (with red dot) into |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ridge Pole with |
|
|
| |||
the ends of the RidgePole |
|
|
|
|
| Red Marking |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
(with red dot). Insert |
|
|
|
|
|
|
|
|
|
|
|
curved end of remaining |
|
|
|
|
|
|
|
|
|
|
|
short Leg Poles into the |
|
|
|
|
|
|
|
|
| Sleeve |
|
|
|
| Curved End of |
|
|
| |||||
|
|
|
|
| with Red |
| |||||
ends of the remaining |
|
|
| Long Leg Pole |
|
|
| ||||
|
|
|
|
|
|
|
|
| Trim |
| |
| Fig. 5 |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
Ridge Poles. (Fig. 5 & 6) |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
11.To stretch tent to finished size:
•Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.10);
•Pull up on top Leg Pole section until tent is taut;
•Twist the lower Leg Pole clock- wise until the button locks into the center or lowest hole;
•Repeat on remaining Leg Poles.
12.Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 11)
Upper
Leg Pole
Section
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Fig. 6
Fig. 11
(continued on other side)