IMPORTANT SAFETY

INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE

USING THIS MIRROR

DANGERTO REDUCE THE RISK OF ELECTRIC SHOCK: ALWAYS UNPLUG THIS mirror

FROM THE ELECTRICAL OUTLET BEFORE CLEANING.

WARNINGTO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR INJURY TO PERSONS:

1.Unplug from outlet before putting on or taking off parts.

2.This mirror should not be used by or near children or individuals with certain disabilities.

3.Use this mirror only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

4.Never operate this mirror if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the mirror to a service center for examination and repair.

5.Keep the cord away from heated surfaces.

6.Never drop or insert an object into any opening.

7.Do not use outdoors.

8.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

9.To disconnect, turn all controls to the off position, then remove plug from outlet.

10.Be sure mirror is not in a position where it can reflect sunlight; reflected sunlight can cause fire.

11.Do not use on a soft surface such as a bed, where openings may be blocked.

12.Touch mirror base until light shuts off, allow unit to cool and unplug cord before replacing light bulbs.

13.Do not place or store mirror where it can fall or be pulled into a tub or sink.

14.If mirror falls into water, unplug it immediately. Do not reach into the water.

15.Never use while sleeping.

16.Do not use bulb greater than 30 watts.

Use in any 120 volt, 60 hertz AC electric outlet (ordinary house current). Do not use it in any other electrical outlet.

17.To protect against electrical hazards, do not use while bathing or in the shower.

18.Unplug the mirror from outlet before cleaning. Do not leave mirror unattended when it is plugged in.

FOR HOUSEHOLD USE ONLY

SAVE THESE

INSTRUCTIONS

Installation instructions

Wall Mount Mirror

1.Remove mounting bracket from base or mirror. Leave long screws in bracket.

2.Using 3/8" drill size, drill two holes in wall the same distance apart as two opposite slots in

bracket. Screw into wall stud if possible. If drilling into stud, use 1/8" drill size. Otherwise insert two wall anchors in holes.

CAUTION: Do not drill into electrical wiring through wall. Check with electrician if necessary.

3.Screw bracket onto wall, into the anchors.

4.Attach mirror to bracket by placing long screws through the two holes in mirror’s base. Secure with knurled nuts. Cord should be facing floor.

OPERATING

INSTRUCTIONS

To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

1.Your lighted makeup mirror features a 1x and 5x magnification for the 8" mirror head.

2.Your lighted makeup mirror will adjust to many different angles. Simply tilt the neck or head backward or forward to adjust to the desired angle. Your mirror will also swivel so that you can use either the normal, flat mirror or the magnifying

mirror located on the opposite side.

3.Plug into any standard wall outlet (120 Volt AC). Turn the rotary switch clockwise to the On

position.

4.After use, turn switch clockwise again to the

Off position.

TO Replace Bulb

CAUTION: TURN OFF POWER AND UNPLUG. ALLOW TO COOL AT LEAST 3 MINUTES BEFORE REPLACING BULB.

NOTE: Do not use a bulb greater than 30 watts. Contact a Conair service center at 1-800-3 CONAIR for replacement bulb information (ask for replacement bulb RP34). Bulbs are $1.50 each including shipping and handling.

1.Unscrew screws from opposite sides of the mirror housing near the rotating hinges (Fig. 1).

2.Carefully lift off the top half of the housing from the bottom half that is affixed to the arm.

3.Unscrew the old bulb and replace with the

new bulb (Fig. 2).

4.Carefully replace the top housing half after locating and aligning the screw holes to the bottom half. If the holes don’t line up, turn top half of mirror 180˚.

5.Insert two screws back into screw holes and tighten with screw driver. Do not over-tighten.

Figure 1

Figure 2

Page 1
Image 1
Conair BE87CR installation instructions Save These Instructions, Operating Instructions, Using this Mirror

BE87CR specifications

The Conair BE87CR is a versatile and innovative hair styling tool designed for those who want to achieve professional-level results at home. This styling brush combines the functionality of a traditional hairbrush with the power of a hair dryer, making it an essential addition to any hair care routine.

One of the standout features of the Conair BE87CR is its unique two-in-one design. The brush not only detangles and styles hair but also dries it efficiently, saving users time and effort in their morning routines. This multi-functionality allows for seamless styling, enabling users to create a variety of looks from sleek and straight to bouncy and voluminous.

The Conair BE87CR employs advanced ionic technology, which helps reduce frizz and enhance shine. By emitting negative ions, the styling brush helps to break down water molecules, ensuring faster drying time while simultaneously conditioning the hair. This technology is particularly beneficial for individuals with thick or curly hair, as it provides a smoother, shinier finish.

With adjustable heat settings, the Conair BE87CR caters to different hair types and styling needs. Users can choose the optimal temperature for their hair, whether it be fine, medium, or thick. This level of customization prevents heat damage and allows for more precise styling, adapting to the individual needs of each user.

The brush features a lightweight and ergonomic design, making it easy to handle during styling sessions. The comfortable grip minimizes hand fatigue, allowing users to style their hair without discomfort. Additionally, the corded design offers unlimited runtime, ensuring that users can achieve their desired look without worrying about battery life.

Another notable characteristic of the Conair BE87CR is its tangle-free cord, which enhances maneuverability during use. The rotating cord ensures that the brush can easily be turned and twisted without getting tangled, helping users navigate around their head with ease.

In conclusion, the Conair BE87CR is packed with features that make it a must-have styling tool. From its innovative two-in-one design and advanced ionic technology to its customizable heat settings and ergonomic build, it is crafted to deliver a high-quality hair styling experience. Whether aiming for a polished finish for a special occasion or a simple everyday style, the Conair BE87CR stands ready to fulfill all styling aspirations while ensuring the health and vibrancy of hair.