IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE. WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE TAKEN, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER
To reduce the risk of electrocution:
1.Always unplug this appliance immediately after using.
2.Do not use while bathing.
3.Do not place or store appliance where it can fall or be pulled into a tub or sink.
4.Do not place in or drop into water or other liquid.
5.Do not reach for an appliance that has fallen into water. Unplug immediately.
1.Read all instructions before using the appliance.
2.To protect against electrical hazards, do not use while bathing or in the shower.
3.Close supervision is necessary when any appli- ance is used by or near children or by individuals with certain disabilities.
4.Unplug the appliance from outlet when not in use and before cleaning. Do not leave appliance unattended when it is plugged in. Keep cord away from heated surfaces.
5.Do not operate this appliance with a damaged cord or plug or if the appliance malfunctions or has been dropped or damaged in any manner. Return appliance to nearest service facility for examination,
electrical or mechanical adjustment, or repair. No repairs should be attempted by the consumer.
6.Use appliance only for intended use as described in this instruction book. The use of attachments not recommended or sold by Conair may cause hazards.
7.Do not use outdoors or operate where aerosol (spray) products are being used, or where oxygen is being administered.
8.Do not use on a soft surface such as a bed, where openings may be blocked.
9.Do not place or store appliance where it can fall or be pulled into a tub or sink.
10.Do not place in or drop into water or other liquid.
11.If an appliance falls into water, unplug it immediately. Do not reach into the water.
Use on any 120 volt 60 hertz AC electric outlet (ordinary household current). Do not use it on any other electrical outlet.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
CHARGING
Your Complete Nail Care Center should be charged using only the charger supplied. Ensure that the switch on the handle is in the "off" position. Connect the appliance to the charger by inserting the small plug at the end of the charger lead into the corresponding socket in the end of the handle. Plug the charger into the mains wall socket. Allow the handle to charge for 16 hours. It is better not to leave the appliance on charge for more than 24 consecutive hours to preserve
the longest possible life of the rechargeable cells.
CORDED USE
1.Ensure that the handle is switched off.
2.Insert the small plug at the end of the charger lead into the corresponding socket in the end of the handle. Plug the charger into the mains wall socket. Wait for one minute, then switch on.
IMPORTANT! Do not use the appliance in this mode for more than 20 minutes.
Your Complete Nail Care Center operates on an AC adapter. Adapter can be plugged into the hous- ing to operate the nail dryer or to recharge the power handle; adapter can also be used to operate the power handle directly by plugging into the bottom of the handle.
The power handle has two interchangeable heads. The rotary head works with round attachments that spin in a circular motion and the linear head works with rectangular plates that move in a
To change heads: twist the head in a counter- clockwise motion and pull up; head comes off. Gently push other head onto plastic base and twist slightly with clockwise motion until head clicks into secure position.
To attach discs or plates: to attach discs or cones to the rotary head, insert metal post of disc into the white plastic tube of head and gently push down. To attach plates to the linear head, match up rounded end of plate with round end of head and snap plate onto head. To remove attachments, simply pull off.
Your Complete Nail Care Center contains a number of attachments. The coarser discs and plates are ideal for shaping and eliminating ragged edges for a clean finish. The finer discs, cones and plates smooth unsightly ridges. The polishing cone and disc provide the flawless smooth surface needed for nail polish applications
and help polish nails to a
To soften nails and cuticles before a manicure, pull out the manicurist’s dish, fill it with warm soapy water and soak your finger tips for a few minutes. Dry your hands thoroughly before using the power handle and attachments.
After you have attached a head and an appropri- ate attachment to the power handle, turn the power handle “on” and carefully start shaping, smoothing or polishing your nails. You can vary the speed at which the attachment moves by turning the speed dial.
Slower speeds give you more control over the filing procedure.
Your power handle also features a light to give you additional illumination when working on a nail.
Your Complete Nail Care Center includes a nail dryer which will help shorten fresh nail polish drying time. Simply insert your hand into the nail dryer, pushing down slightly. That will start the nail dryer. Check nails after a few minutes to see if polish is dry.
After using the Complete Nail Care Center
several times, you will find the attachment and speed combinations that give you the results you desire.
MANICURE
1.Soak your nails in warm soapy water, then dry thoroughly.
2.Decide on the nail shape you want.
The three most common nail shapes are round, square, or square with rounded edges.
3.Use the Smoothing Disc/Plate to smooth the edges of each nail. Then use the rounded end of the Cuticle Shaper to gently push the cuticles away from the nail plate. If desired, massage lotion or cream into the cuticle to help soften cuti- cle and promote healthy nails. Unwanted rough or hard skin can be reduced by using the Sapphire Cones and/or a Smoothing Disc. The side of the pointed Sapphire Cone may be used to carefully
