Craftsman 172.74544 warranty SAFETY INSTRUCTIONS cont, ELECTRICAL SAFETY cont, Extension Cords

SAFETY INSTRUCTIONS cont.

ELECTRICAL SAFETY cont.

!WARNING: GFCI (Ground Fault Circuit Interrupter) protection should be provided on all circuits or outlets to be used for electric lawn and garden power tools. Receptacles are available having built-in GFCI protection and should be used for this measure of protection.

!CAUTION: This trimmer has a 12-in. Pigtail Power Cord that must be plugged into a proper extension cord (see below).

!WARNING: Double insulation DOES NOT take the place of normal safety precautions when operating this tool.

3.BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within

the voltage marked on the tool’s data plate. DO NOT use “AC only” rated tools with a DC power supply.

4.DO NOT expose tools to rain or wet conditions or use electric tools in wet or damp locations. Water entering an electric tool will increase the risk of electric shock.

5.If operating an electric tool in damp locations is unavoidable, ALWAYS USE a Ground Fault Circuit Interrupter to supply power to your tool. ALWAYS WEAR electrician’s rubber gloves and footwear in damp conditions.

6.When operating a power tool outside, ALWAYS use an outdoor extension cord marked “W-A” or “W”. these cords are rated for outdoor use and reduce the risk of electric shock.

7.INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears Service Center. BE SURE to stay constantly aware of the cord location and keep it well away from the spinning cutting lines.

8.DO NOT abuse the cord. NEVER use the cord to carry the tool by or to pull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

EXTENSION CORDS

Use a proper extension cord. ONLY use cords listed by Underwriters Laboratories (UL). Other extension cords can cause a drop in line voltage, resulting in a loss of power

and overheating of tool.

For this tool an AWG (American Wire Gauge) size of a least 14-gauge is recommended for an extension cord of 25- ft. or less in length. Use 12-gauge for an extension cord of 50-ft. Extension cords 100-ft. or longer are not recommended.

Remember, a smaller wire gauge size has greater capacity than a larger number

(14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire has more capacity than 14-gauge). When in doubt use the smaller number.

When operating a power tool outdoors, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

!CAUTION: Keep the extension cord clear of the work area. Position the cord so that it will not get caught on bushes, hedges, tree trunks, lawnmowers or other obstructions while you are working with the trimmer.

6

SAFETY INSTRUCTIONS cont.

EXTENSION CORDS cont.

!WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock, resulting in serious injury.

The label on your tool may include the following symbols.

V			Volts
A			Amps
Hz			Hertz
W			Watts
min			Minutes
	....................................................................		Alternating current
		..................................................................	Direct current
no			No-load speed
	....................................................................		Class II construction, Double Insulated
RPM………………………............................. . .Revolutions per minute
SPM…...........................…………………….....Strokes per minute
OPM………………..........................………..... Orbits per minute
!	....................................................................		Indicates danger, warning or caution.
			It means attention! Your safety is involved.

SERVICE SAFETY

1.If any part of this trimmer is missing or should break, bend, or fail in any way; or should any electrical component fail to perform properly: SHUT OFF the power switch and remove the trimmer plug from the power source and have the missing, damaged or failed parts replaced BEFORE resuming operation.

2.Tool service should be performed at a Sears Parts and Repair Center. Service or maintenance performed by unqualified personnel could result in a risk of injury.

3.When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

SAFETY RULES FOR ELECTRIC TRIMMERS

1.KNOW your electric trimmer. Read operator’s manual carefully. Learn the applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire or serious injury.

2.DO NOT use trimmer without adequate lighting. ALWAYS make sure that you can see what you are trimming and edging.

3.Use trimmer ONLY when grass and weeds are dry.

4.ALWAYS remove objects such as stones, sticks, and debris from the trimming/edging path that could become entangled in, or thrown by, the trimmer.

5.ALWAYS hold the trimmer by both the main rear handle and the auxiliary handle for greater control and balance. NEVER reach under the safety guard.

6.AVOID accidental starting. DO NOT carry a plugged in trimmer with your finger on the switch.

7