STEP 9: (SEE FIGURE 9)
Install the Rear Locating Bracket to the top of the Rear Mounting Bracket using two 3/8" x 1" Carriage bolts (H) and 3/8" nylock nuts (K). Tighten nuts Install the Rear Support Channels to the middle set of holes in the sides of the Rear Mounting Bracket using four 3/8" x 1" Carriage Bolts (H) and 3/8" nylock nuts
(K). Finger tighten only.
REAR LOCATING |
| REAR SUPPORT | ||||
| CHANNELS | |||||
BRACKET |
| |||||
|
| |||||
|
|
|
|
|
| 3/8" X 1" |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| CARRIAGE BOLT (H) |
REAR MOUNTING |
| 3/8" NYLOCK NUT (K) | ||||
| ||||||
BRACKET |
| |||||
|
| |||||
FIGURE 9
STEP 10: (SEE FIGURE 10)
Slide the Rear Support Channels under the rear of the tractor. Attach the Rear Mounting Bracket to the Tractor Drawbar using the 5/8" x
5/8" X | TRACTOR | |
CLEVIS PIN (Q) | DRAWBAR | |
REAR MOUNTING | REAR LOCATING | |
BRACKET | ||
BRACKET | ||
| ||
LARGE | REAR SUPPORT | |
HAIRPIN | ||
CHANNEL | ||
COTTER (U) | ||
|
FIGURE 10
STEP 11: (SEE FIGURE 11)
Slide the Thrust Channel under the front of the tractor. Attach the Hanger Brackets to the Frame Brackets using two 1/2" x 1" clevis pins (R), 1/2" washers (P) and large hairpin cotters (U).
1/2" WASHER (P) 
LARGE HAIRPIN COTTER (U) 1/2"X 1" CLEVIS PIN (R)
FIGURE 11 - SEARS TRACTOR SHOWN
STEP 12: (SEE FIGURE 12)
Place the rear of the Thrust Channel between the two Rear Support Channels. Install four 3/8" x 1" carriage bolts (H) and 3/8" nylock nuts (K) using the most widely spaced holes that are aligned with slots.
Finger tighten only.
If the Rear Support Channels bump against bottom of the tractor, reattach the rear of the channels to a lower set of holes in the Rear Mounting Bracket. If there is more clearance than necessary between the Rear Support Channels and the bottom of the tractor, reattach the rear of the channels to a higher set of holes in the Rear Mounting Bracket.
•Spread the Hanger Brackets apart as far as possible and center the Thrust Channel under the tractor. Tighten all bolts and nuts installed up to this point.
•Measure the height of the front plate on the Thrust Channel. If it is not 4" to 5" above the ground, reinstall the clevis pins in the Hanger Brackets to a higher or lower hole position to attain the correct height.
REAR |
|
|
|
|
|
|
SUPPORT | 3/8" X 1" |
|
|
|
|
|
CHANNEL |
|
|
|
| 5" | |
| CARRIAGE BOLT (H) | 4" | to | |||
|
| |||||
|
|
|
| |||
|
| FRONT |
|
|
| |
| 3/8" NYLOCK |
|
|
|
| |
| GROUND | |||||
| NUT (K) | PLATE | ||||
|
|
|
|
| ||
FIGURE 12 - SEARS TRACTOR SHOWN
STEP 13: (SEE FIGURE 13)
Assemble the pivot support bracket to the front of the Thrust Channel using four 3/8" x 1" carriage bolts (H) and four 3/8" nylock nuts (K). Make sure the bracket is straight and then tighten.
3/8" NYLOCK NUT (K)
3/8" X 1"
CARRIAGE BOLT (H)
FIGURE 13 - SEARS TRACTOR SHOWN
10