TROV LESHOO G POUNT$
PROBLEM | CAUSE | CORRECTION |
Engine continues to run when operator leaves sea with attachment clutch
engaged
Poor cut - uneven
Mower blades will not rotate
t.Faulty operator_safety presence control system
t.Worn, bent or loose blade. 2_ Mower deck not level.
3.Buildup of grass, leaves, and trash under mower..
4.Bent blade mandrel.
5.Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrelsr
t.Obstruction in clutch mechanism
2.Worn/damaged mower drive belt.
3Frozen idler pulley.
4.Frozen blade mandrel.
1.Check wiring, switches and connections It not corrected, contact an authorized service center/ department
tReplace blade. Tighten blade bolt..
2 Level mower deck.
3Clean underside of mower housing.
4Replace blade mandrel..
5Clean around mandrels to open vent holes
1.Remove obstruction
2 | Replace | mower drive belt | |
3 | Replace | idler | pulley.. |
4 | Replace | blade | mandrel. |
Poor grass discharge | 1. | Engine | speed | too | slow |
| |||||
| 2. | Travel | speed | too fast |
| ||||||
| 3. | Wet | grass |
|
|
|
|
|
| ||
| 4. | Mower | deck | not level |
| ||||||
| 5. | Low/uneven |
| tire air pressure |
| ||||||
| 6. | Worn, | bent | or loose | blade. |
| |||||
| 7. | Buildup of grass, leaves and trash under mower. | |||||||||
| 8. | Mower | drive | belt |
| worn |
| ||||
| 9. | Blades | tmproperfy | installed |
| ||||||
| 10 | Improper | blades | used |
| ||||||
| 11 | Clogged | mower | deck vent holes from buildup of | |||||||
|
| grass, leaves, and trash around mandrels. | |||||||||
Headlight(s) not working | 1. | Switch | is "OFF'. |
|
|
|
| ||||
(if so equipped) | 2 | Bulb(s) | burnedout. |
|
|
| |||||
| 3. | Faulty | light | switch. |
|
| |||||
| 4. | Loose | or damaged | wiring. |
| ||||||
| 5 | Blown | fuse |
|
|
|
|
|
| ||
Battery will not charge | t.. | Bad | battery | cell(s). |
|
| |||||
|
|
| |||||||||
| 2_ | Poor | cable | conneclions |
| ||||||
| 3. | Faulty | regulator | (if so equipped) |
| ||||||
| 4. | Faulty | alternator. |
|
|
|
| ||||
Loss of drive | 1 | Freewheel | control | in "disengaged" | position.. | ||||||
| 2. | Motion | drive | belt |
| worn, damaged, | or broken. | ||||
| 3. | Air trapped | in transmission during | shipment | |||||||
|
| or servicing. |
|
|
|
|
|
| |||
Engine "backfires" | 1. | Engine | throttle control not set at "SLOW" | ||||||||
when turning engine |
| position | for | 30 seconds before stopping engine. | |||||||
"OFF" |
|
|
|
|
|
|
|
|
|
|
|
1. | Place thrott[e control in "FAST" position° |
2 | Shift to slower speed, |
3.Allow grass to dry before mowing
4.Level mower deck..
5.Cheek tires for proper air pressure.
6.Replace/sharpen blade. Tighten blade bolt
7.Clean underside of mower housing..
8, Replace mower drive bell
9_ Reinstall blades sharp edge down
10 Replace with blades listed in thts manual.
11.Clean around mandrels to open vent holes
1.Turn switch "ON"
2Replace bulb(s).
3Check/replace light switch.
4.Check wiring and connections.
5Replace fuse.
1.Replace battery,
2.Check/clean all connections,
3.Replace regulator,
4..Replacealternator0
t Place freewheel control in "engaged" position..
2.Replace motion drive belt
3.Purge transmission
1.Move throttle control to "SLOW" position and allow to idle for 30 seconds before stopping engine.
29