TROUBLESHOOTINGCHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM

CAUSE

 

 

 

CORRECTION

Mower blades will

2.

Worn/damaged

mower

2.

Replace mower drive belt.

not rotate (con't)

 

drive belt.

 

 

 

 

 

3.

Frozen

idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Contact aSears or other

 

 

 

 

 

 

 

qualified service center.

Poor grass

1.

Engine speed too slow.

1.

Place throttle control in

 

=FAST" position.

discharge

 

 

 

 

 

 

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

 

 

3.

Allow grass to dry before

 

 

 

 

 

 

 

mowing.

 

4.

Mower

deck

not

level.

4.

Level mower deck.

 

5.

Low/uneven

tire

air pressure

5.

Check tires for proper air

 

 

 

 

 

 

 

pressure.

 

6.

Wom,

bent or loose blade.

i6.

Replace/sharpen blade.

 

 

 

 

 

 

 

Tighten blade bolt.

 

7.

Buildup of grass, leaves and

7.

Clean underside of mower

 

 

trash under mower.

 

housing.

8.Mower drive belt worn.

9.Blades improperly installed.

8.Replace mower drive belt.

9.Reinstall blades sharp edge down.

10.1mproper blades used.

11 .Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.

10.Replace with blades listed in this manual.

11 .Clean around mandrels to open vent holes.

Headlight(a)

not

1.

Switch

is =OFP.

 

1.

Turn switch =ON'.

working

 

2.

Bulb(s) or lamp(s)

bumed out.

2.

Replace

bulb(s)

or lamp(s).

(if so equipped)

3.

Faulty

light switch.

 

3.

Check/replace

light switch.

 

 

4.

Loose

or damaged

wiring.

4.

Check wiring and connec-

 

 

 

Blown fuse.

 

 

tions.

 

 

 

 

 

 

5.

 

5.

Replace

fuse.

 

 

Battery will

not

1.

Bad battery cell(s).

1.

Replace

battery.

 

charge

 

2.

Poor cable connections.

2.

Check/clean

all connec-

 

 

 

 

 

 

 

tions.

 

 

 

 

 

 

3.

Faulty regulator

 

3.

Replace

regulator.

 

 

 

(if so equipped).

 

 

 

 

 

 

 

 

 

4.

Faulty alternator.

 

4.

Replace

alternator.

Loss of drive

1.

Freewheel control in

1.

Place

freewheel

control in

 

 

2.

=disengaged" position.

 

=engaged"

position.

 

 

Motion drive belt wom,

2.

Replace

motion

drive belt.

 

 

3.

damaged, or broken.

 

 

 

 

 

 

 

 

Air trapped in transmission

3.

Purge

transmission.

 

 

 

during shipment or

 

 

 

 

 

 

 

 

 

servicing.

 

 

 

 

 

 

 

Engine "backfires" whenturnlng engine

"OFF"

1. Engine

throttle

control not

. Move throttle control to

set at "SLOW _

 

=SLOW" position and allow

position

for 30

seconds

to idle for 30 seconds before

before

stopping

engine.

stopping engine.

32

Page 32
Image 32
Craftsman 917.272281 owner manual Problem Cause Correction