Cres Cor CO-151-FPW-UA-12B-Q1 manual Short Form Specifications

CO-151-FPW-UA-12B-Q1

DETAIL OF

PAN SLIDE

CRES COR	PAN			DIM “A”	DIM “B”	DIM “C”	INSIDE DIMENSIONS				WEIGHT
MODEL NO.	CAP/ANGLES	SIZE		WIDTH	DEPTH	HEIGHT	WIDTH	DEPTH	HEIGHT		ACT.
	12	SEE NOTE	IN	28-3/4	37-3/4	73-1/2	21-1/4	26-1/2	58	LBS	403
CO-151-FPW-UA-12B-Q1
	SETS	BELOW	MM	740	960	1870	540	675	1475	KG	183

NOTE: Refer to pan size chart at end of section.

ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.

CABINET:

•Body: 22 ga. 304 stainless steel.

•Reinforcement: Internal framework of 16 ga. stainless steel.

•Insulation: Fiberglass, thermal conductivity (K factor) is .23 at 75˚F. 1-1/2" in back wall, doors, base; 2" in side walls.

•Water pan: 4 Gallons; 16 ga. stainless steel with 1850 Watt heater and with petcock drain; mounted to base.

•Drip trough: Formed 18 ga. stainless steel; mounted to lower front and rear of cabinet; removable drip pan.

•Air tunnels (2): 20 ga. stainless steel, lift-out type, mounted on side walls.

•Push/pull handles (4): 7" vertical; recessed.

BASE:

•One piece construction, .125 aluminum.

•Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap. 250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front casters equipped with brakes.

DUTCH DOORS:

•Field reversible.

•Formed 22 ga. 304 stainless steel.

•Latches: Chrome plated zinc with composite handle, ceramic magnetic type; mounted inboard.

•Hinges: Heavy duty chrome plated zinc, mounted inboard.

•Gaskets: Perimeter type, silicone.

•Pan stops: Embossed.

PAN SLIDES:

•Stainless steel wire universal angles (.306 dia.) mounted on lift-out posts.

•12 sets of angles adjustable on 1-1/2" centers.

•Grids (6): Nickel chrome plated steel, raised wire 17" x 25".

POWER REQUIREMENTS AVAILABLE:

•8200 Watts, 208 Volts, 60 Hz., 1 phase, 39 Amps., 50 Amp. service.

•8200 Watts, 240 Volts, 60 Hz., 1 phase, 34 Amps., 50 Amp. service.

•8200 Watts, 208 Volts, 60 Hz., 3 phase, 23 Amps., 30 Amp. service.

•8200 Watts, 240 Volts, 60 Hz., 3 phase, 20 Amps., 30 Amp. service.

®

5925 Heisley Road • Mentor, OH 44060-1833 Phone: 877/CRESCOR • Fax: 440/350-7267 www.crescor.com

POWER UNIT COMPONENTS: (refer to above drawing)

• Body:Formed 304 stainless steel with black control panel, recessed and tilted 7˚.

A)Thermostat (microprocessor)

• Holding up to 250˚F (121˚C)

• Cook/Retherm up to 350˚F(176.5˚C)

• Thermometer

B)Thermostat (humidity): Solid state

C)Switch: Lighted ON-OFF rocker type.

D)Pilot light for low water level.

•Power cord:Permanent, 8ft., 6/3 ga.with right angle plug.

•Air heaters (3): 2670 Watts each.

•Water heater: 1850 Watts.

•Blower motors (3).

•Vent fans (2).

•Fuses (2): 3 amp.

•Probes (2): 1-1/2” and 6”, stainless steel.

INSTALLATION REQUIREMENTS:

• Check local vent hood codes for mobile Roast-N-Hold ovens.

SHORT FORM SPECIFICATIONS

Cres Cor Pass-Thru AquaTemp Roast-N-Hold Convection Oven Model CO-151-FPW-UA-12B-Q1. Removable power unit 20 ga. 304 stainless steel, recessed control panel. Two stainless steel probes, 1-1/2 and 6” long. Cabinet 22 ga. 304 stainless steel. Stainless steel internal frame; coved corner interior. Dutch doors front and back, 22 ga. 304 stainless steel, ceramic magnetic latch, heavy duty hinges. 16 ga. stainless steel water reservoir, 4 gallon capacity. Fiberglass insulation in sides 2”; back, doors and base 1-1/2”. (12) sets universal angles for multiple pan sizes and spacing. One piece base .125 aluminum. 5" swivel modulus casters, Delrin bearings. Load capacity 250 lbs. each. 8200 Watts,

Volts, 60 Hz.,	Phase. 2 year parts warranty. Provide
the following accessories:		__ . UL, CUL, UL
Sanitation listed.

In line with its policy to continually improve its products, CRES COR reserves the right to change materials and specifications without notice.

© Crescent Metal Products, Inc. 1998 All rights reserved. Litho in U.S.A.