Cres Cor CO-151-HUA-6B Short Form Specifications, Cabinet, Base, Door, Installation Requirements

CO-151-HUA-6B

DETAIL OF

6-30P

L15-20P

PAN SLIDE

CRES COR

PAN

DIM “A”

DIM “B”

DIM “C”

INSIDE DIMENSIONS

WEIGHT

MODEL NO.

CAP/ANGLES

SIZE

WIDTH

DEPTH

HEIGHT

WIDTH

DEPTH

HEIGHT

ACT.

CO-151-HUA-6B

6

SEE NOTE

IN

28-3/4

37-3/4

43-3/4

21-1/4

26-1/2

28

LBS

296

SETS

BELOW

MM

740

960

1115

540

675

715

KG

134

Note: Refer to pan size chart at end of section.

ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.

CABINET:

•Body: 22 ga. 304 stainless steel.

•Reinforcement: Internal framework of 16 ga. stainless steel.

•Insulation: Fiberglass, thermal conductivity (K factor) is .23 at 75˚F. 1-1/2" in back wall, door, base; 2” in side walls.

•Air tunnel: 20 ga. stainless steel, lift-out type; mounted on rear wall.

•Work Top: 18 ga., 304 stainless steel.

BASE:

•One piece construction, .125 aluminum.

•Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap. 250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front casters equipped with brakes.

DOOR:

•Field reversible.

•Formed 22 ga. 304 stainless steel.

•Latch: Chrome plated steel, high temperature ceramic magnetic type; mounted inboard.

•Hinges: Heavy duty chrome plated steel, lift-off type; mounted inboard.

•Gasket: Perimeter type, silicone.

•Pan stops: Embossed.

POWER UNIT COMPONENTS: (refer to above drawing)

•Body: Formed 20 ga. 304 stainless steel with black control panel, recessed and tilted 7˚.

A)Thermostat (holding): Solid state, room ambient to 250˚F. (121˚C.).

B)Thermostat (cook/retherm): Solid state, room ambient to 350˚F. (176.5˚C.).

C)Pilot lights (2).

D)Switch: Lighted ON-OFF rocker type.

E)Timer: 24 hr. digital countdown; infinite memory retention.

F)Thermometer.

•Power cord: Permanent, 6 ft., 10/3 ga. with right angle plug.

•Heaters (3): 1470 Watts each.

•Blower motors (3).

•Vent fans (2).

•Fuses (2): 3 Amp.

INSTALLATION REQUIREMENTS:

• Check local vent hood codes for mobile Roast-N-Hold ovens.

SHORT FORM SPECIFICATIONS

PAN SLIDES:

•Wire angles (.306 dia.), nickel chrome plated; mounted on lift-out posts.

•(6) sets of angles adjustable on 1-1/2" centers.

•Grids (3): Nickel chrome plated steel, raised wire 17” x 25”.

POWER REQUIREMENTS AVAILABLE:

•4700 Watts, 208 Volts, 60 Hz., 1 phase, 24 Amps., 30 Amp. service.

•4700 Watts, 240 Volts, 60 Hz., 1 phase, 20 Amps., 30 Amp. service.

•4700 Watts, 208 Volts, 60 Hz., 3 phase, 13 Amps., 20 Amp. service.

•4700 Watts, 240 Volts, 60 Hz., 3 phase, 12 Amps., 20 Amp. service.

®

5925 Heisley Road • Mentor, OH 44060-1833 Phone: 877/CRESCOR • Fax: 440/350-7267 www.crescor.com

Cres Cor Roast-N-Hold Half Size Convection Oven Model CO-151-HUA-6B. Removable power unit 20 ga. 304 stainless steel, recessed control panel. Cabinet and door 22 ga. 304 stainless steel; stainless steel internal frame; coved corner interior. Fiberglass insulation in sides 2”; back, door and base 1-1/2”. High temperature magnetic latch. (6) sets universal angles for multiple pan sizes and spacing. One piece base .125 aluminum. 5" swivel modulus casters, Delrin bearings. Load

capacity 250 lbs. each. 4700 Watts,				Volts,
60 Hz.,	Phase. 2 year parts warranty. Provide
the following accessories:		_	.
UL Sanitation, UL, CUL listed.

In line with its policy to continually improve its products, CRES COR reserves the right to change materials and specifications without notice.

© Crescent Metal Products, Inc. 2002 All rights reserved Litho in U.S.A.