DSi 2000

D S i S E R I E S

Architectural & Engineering Specifications

DSi 2000

The Crown® DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor. The DSi 2000 shall be THX® approved.

The outputs shall be usable as stereo or bridged-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage.

Front panel controls and indicators shall include the following: Level: Detented rotary level control, one per channel.

Power Switch: On/off switch applies AC power to the amplifier.

Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.

LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.

Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.

–10 Indicator: Green LED flashes when output signal exceeds –10 dB below clip.

–20 Indicator: Green LED flashes when output signal level exceeds –20 dB below clip.

Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.

Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.

Temp Indicator: Red LED, one per channel, illuminates under excessive tem- perature conditions.

Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power.

Rear panel controls and connectors shall include the following: AC Line Connector: NEMA 5-15P (15A).

Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.

Output Connectors: 4-position barrier strip with connectors for dual louspeak- ers or bridge-mono loudspeaker.

HiQnet USB Connector: Type B, connects to a HiQnet network.

HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.

The amplifier shall have the following specifications:

Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm

Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W

with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-

Mono: 1,600W with 0.5% THD.

Voltage Gain at 1kHz: 32.9 dB.

Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.

Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode.

Sensitivity at 8 ohm rated output: 1.4V.

Sensitivity at 4 ohm rated output: 1.2V.

Sensitivity at 2 ohm rated output: 1.0V.

Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB (A weighted).

Damping Factor: Better than 500 from 20 Hz to 500 Hz.

Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz, A-weighted.

Input Stage: Input is electronically balanced and employs precision 1% resis- tors.

Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.

AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V, 50/60 Hz.

AC Line Current: 11.93A.

At Idle: Draws no more than 45 watts.

Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condens- ing).

The DSP section shall have the following specifications:

Input EQ: 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.

Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave, Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB band- pass gain and polarity control.

Output EQ: 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can NOT be bypassed. Filters are enabled individually.

Output Limiter: Prevents clipping and protects loudspeakers. Choice of –3, –6, or –12 dB threshold per channel.

Delay: Up to 50 msec total delay per channel.

Presets: 20 presets. One is “DSP OFF.” Fifteen are factory-set for JBL Cinema systems. Four are user-definable.

Protection shall include the following:

DSi-Series amplifiers shall be protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; excessive output current, and input overload damage. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients

The chassis shall be steel. Cooling shall be by a proportional speed fan with front-to-rear airflow.

Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5 in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.

Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)

The amplifier shall be designated the Crown DSi 2000.

Crown International 1718 W. Mishawaka Rd. Elkhart, IN 46517-9439 TEL: 574-294-8200 FAX: 574-294-8FAX www.crownaudio.com

Specifications subject to change without prior notice. Latest information available at www.crown- audio.com.

Crown and Crown Audio are registered trademarks of Crown International, Inc. Printed in U.S.A.

© 2007 Crown Audio®, Inc.

10/07

139684-1F

Page 1
Image 1
Crown Audio DSi 2000 specifications I S E R I E S Architectural & Engineering Specifications

DSi 2000 specifications

The Crown Audio DSi 2000 is a robust and versatile power amplifier designed specifically for commercial audio applications, where reliability and performance are critical. With a powerful output of 2000 watts, this amplifier excels in delivering high-quality sound in a variety of settings, including live performances, installations, and public address systems.

One of the standout features of the DSi 2000 is its advanced DSP (Digital Signal Processing) capabilities. This built-in DSP allows for precise control over the audio output, enabling users to fine-tune their sound with features like equalization, compression, and feedback suppression. These tools help ensure optimal sound quality while effectively managing any potential acoustic challenges.

The amplifier is equipped with Crown’s patented DriveCore technology, which significantly enhances its efficiency compared to traditional amplifiers. DriveCore combines the functionality of an amplifier’s entire output stage into a single chip, providing impressive power output while consuming less space and energy. This technology also contributes to the amplifier’s lightweight design, making it easier to transport and install.

The DSi 2000 supports a variety of input options, including analog, digital, and balanced XLR connections. This flexibility allows users to integrate the amplifier seamlessly into existing audio systems. Additionally, with its full-range frequency response capability, the DSi 2000 is suitable for driving a wide range of speakers, from subwoofers to high-frequency drivers.

In terms of reliability, the Crown DSi 2000 is built to withstand the rigors of demanding environments. Its robust construction includes thermal protection and overload circuitry, ensuring that the amplifier performs safely under extreme conditions. The unit is also designed with efficient cooling systems to prevent overheating during prolonged use, further enhancing its durability.

Users will appreciate the front panel’s intuitive interface, featuring LED indicators that provide real-time feedback on the amplifier's status. The amplifier also includes rear-panel control options, allowing for easy access to audio adjustments and settings management.

Overall, the Crown Audio DSi 2000 represents a perfect blend of power, efficiency, and advanced technology. Its feature set makes it an ideal choice for professionals needing reliable and top-quality sound reinforcement. Whether in a small venue or a large auditorium, the DSi 2000 is equipped to deliver exceptional audio performance, ensuring an immersive listening experience.
Top Page Image Contents