IQ-PIP- USP3/CN
U L T R A S E R I E S
IN USE/ | LINK/ |
CONDUCTOR ACTIVITY
he Crown®
mable Input Processor) input module for PIP2™ compatible amplifiers.* It connects the amplifier to a 100 Mb Ethernet network allow- ing it to be remotely controlled and monitored via System Architect or IQwic™ software. In addition, the USP3/CN allows the transport of
The USP3/CN is a HiQnet and TCP/IQ series component and connects to the audio con- trol/monitor network using a standard 100Mb Ethernet hardware (switches, Network Interface Cards, and cables). CobraNet™ audio is avail- able over the same 100Mb Ethernet network, providing a simple to install, single plug solution for audio distribution, control, and monitoring.
The USP3/CN’s SHARC DSP processor gives the user an enormous amount of digital signal
Features
• 100Mb Ethernet | • | Input compressors and output limiters for each | |
CobraNet audio, and HiQnet or TCP/IQ control |
| channel | |
|
| ||
and monitoring | • | Dual, uncorrelated noise generators for noise | |
• Analog audio inputs allow CobraNet network |
| masking | |
• | Sine generator | ||
audio input, CobraNet audio backup, or a hard- | |||
wire emergency override of CobraNet audio | • | Load supervision | |
| |||
• “Listen Bus” amplifier output monitor via | • | Full error reporting | |
|
CobraNet
• 24 bit digital to analog conversion with 32 bit, | • Firmware upgrades via the network | |
• 10 user selectable presets | ||
floating point DSP processing | ||
• Reliable FLASH memory backup of all param- | ||
• 64 assignable filters with 9 different filter types | ||
eters | ||
including | ||
• Three Year, | ||
• Over 2 seconds of delay available per | ||
ranty completely protects your investment and | ||
channel | ||
guarantees its specifications | ||
|
processing. Audio routing, faders, meters, polarity & mute, input compressors, filters, delays, multimode output limiters, error report- ing, and load monitoring are all available. A built in noise generator and
Offering crisp, clear sound and the wide dynamic range possible with CobraNet, the IQ-
The
For more details about the Crown
*You must have a
ible, look for the 
logo on the back of the amplifier. The
Specifications
General
Internal Controls: A Reset/Preset switch, accessible with a straightened paper clip through the PIP panel, selects the next user preset if pressed for less than 2 seconds, resets the PIP to preset “0” if pressed for more than 2 seconds.
Connectors:
Balanced Audio Input Connector
Single
AUX Connector
Configurable for AUX input or AUX output. Listen Bus is available through CobraNet.
Network Connector
The dual RJ45 CobraNet connectors allow a Primary & Secondary connection to the 100Mb Ethernet network. Should the Primary con- nection lose link activity with the network,
the USP3/CN will automatically switch to the Secondary connection to ensure uninterrupted audio and control. The indicators on the RJ45 connectors display network information con- cerning the Ethernet and CobraNet connections.
Indicators:
Preset Indicator
Signals the number of the current preset, if active, by flashing a series of flashes equal to the current preset number.
IQ Data Indicator
Flashes when the
Switches:
Reset/Preset Switch
Used to change presets, restore settings to fac- tory default or restore all the presets to the fac- tory defaults. During operations of the switch, the Data indicator flashes as an aid to the user.
Memory Backup: 512 kbyte
Communications: 100Mb Fast Ethernet con- forming to IEEE 802.3.
Power Requirements (provided by the ampli- fier): +24VDC @ 350mA,
Overall Audio Performance:
DSP Processing: 32 bit, Floating Point, 665 µs latency.
DAC Conversion: 24 bit, 135 µs latency.
Dynamic Range: 103 dB typical
Distortion: < 0.05% THD+N,
Frequency Response: ± 0.5 dB,
Input/Output Monitor Accuracy: Typically
±1dB.
