Fig. 4

Fig. 5

 

0.33in. (8.2 mm)

 

 

 

 

 

 

 

 

0.975 in.

0.75 in.

 

 

 

Shield

 

 

 

 

 

 

 

(24.8 mm) (19 mm)

 

 

 

PCC-130SPP

Audio Return

Audio Hot

PCC-130

If the microphone is used on a lectern, place it on an open surface, not in a cavity. Otherwise the frequency response and polar pattern will be degraded. Set BASS-TILT to BOOST.

The PCC includes two keyhole slots in its base to accept mounting screws for permanent mounting. To screw the PCC to a table top, fol- low this procedure:

1.Punch out the keyholes marked on the label underneath the base plate (use a razor blade, small screwdriver, etc.).

2.Using the template below (Fig. 6), mark the location of two holes in the table where you want to mount the mic. These holes are 1.6 inch (4 cm) apart, center-to-center. They are 1.56 inches (3.96 cm) from the rear of the mic.

3.Screw two #8 woodscrews (0.27-in. or

7-mm diameter head) into the table at the locations you marked.

Fig. 6

1.6in. (4 cm)

Architects’ and Engineers’ Specifications

The microphone shall be the Crown Model PCC-130. The microphone shall be a half-cardi- oid electret condenser type, utilizing a submin- iature transducer of rugged construction.

The microphone shall employ the principle of phase coherency achieved by mounting a small-diameter element very near a boundary, thus eliminating comb filtering in the audible spectrum. The microphone will exhibit excellent off-axis response and gain-before-feedback.

A 15-foot (4.6-m), two-conductor shielded cable with TA3F and A3M connectors shall be supplied with the microphone. As an option, the microphone may be obtained with a bot- tom-mounted stereo phone plug (model PCC- 130SPP, no cable provided).

Nominal sensitivity shall be 22 mV/Pa. Maxi- mum SPL shall be 120 dB SPL for 3% THD. Equivalent noise shall be 22 dBA nominal.

Frequency response shall be 50 Hz to 20,000 Hz with a uniform off-axis response, over 20 dB down at the rear null.

The Crown PCC-130 is specified.

Warranty

Crown professional microphones are guaran- teed against malfunction for a period of three years from date of original purchase. See enclosed warranty sheet for additional informa- tion.

Service

If the microphone does not function properly, check that it is aimed correctly and is config- ured and connected as described in this data sheet. If there is hum or no signal, first repair or replace the cable. If the microphone capsule is defective, order a replacement PCC-130 mic capsule from Crown (part no. M43197-9) or return the microphone in its original packaging to: Crown Factory Service, 1718 West Misha- waka Road, Elkhart, IN 46517-9439.A Service Return Authorization (SRA) is required for product being sent to the factory for service. An SRA can be completed on line at www. crownaudio.com/support/factserv.htm.For further assistance or technical support call 800- 342-6939.

Crown International, Inc. 1718 W. Mishawaka Rd. Elkhart, IN 46517-9439 TEL: 574-294-8000 FAX: 574-294-8FAX www.crownaudio.com

© 2008 Crown Audio®, Inc. Specifi cations subject to change without prior notice. Latest information available at www.crownaudio.com. Crown, Crown Audio, PCC and Phase Coherent Cardioid are registered trademarks of Crown International, Inc.

4/08

126627-8

 

 

 

 

Page 1
Page 2
Image 2
Crown Audio PCC-130 specifications Architects’ and Engineers’ Specifications, Warranty, Service
Page 1

PCC-130 specifications

The Crown Audio PCC-130 is a high-performance programmable powered microphone designed primarily for professional audio applications. This microphone is a popular choice among sound engineers and system designers due to its exceptional performance and reliable construction. With its integrated microphone preamp and advanced technologies, the PCC-130 excels in capturing sound while minimizing noise interference.

One of the standout features of the PCC-130 is its low-profile design, which allows it to blend seamlessly into various environments, including conference rooms, lecture halls, and theaters. The microphone's unobtrusive appearance makes it an ideal choice for applications where aesthetics are a concern, while still delivering superior audio quality.

The PCC-130 employs a high-quality electret condenser element, which is known for its wide frequency response and exceptional transient response. This translates to clear and natural sound reproduction, ensuring that every nuance of the audio is captured accurately. The microphone is particularly effective in picking up speech, making it an excellent choice for public speaking engagements and presentations.

Another significant advancement of the PCC-130 is its built-in programmable features, which allow users to customize settings to suit specific requirements. With the ability to adjust gain levels, frequency response, and sensitivity, this microphone can be tailored to the acoustics of any space. This level of customization enhances the user experience and ensures optimal performance in various settings.

Additionally, the PCC-130 offers multiple connectivity options, including XLR and TRS outputs, making it compatible with a wide range of audio equipment. This versatility enables seamless integration into existing audio systems, providing flexibility for audio professionals.

The microphone’s sturdy construction ensures durability and longevity, important traits for devices used in high-demand environments. The PCC-130 is designed to withstand the rigors of regular use while maintaining top-notch performance standards.

Incorporating advanced technologies and features, the Crown Audio PCC-130 is a testament to Crown's commitment to quality in audio engineering. Whether for live sound applications or recorded settings, the PCC-130 stands out as a versatile and dependable microphone choice for professionals in the audio industry, making it an essential tool for anyone serious about sound.
Top Page Image Contents