Crown Audio PCC-130SW Warranty, Service, Operation, Architects’ and Engineers’ Specifications

Fig. 4

2.5"

6.4 cm

.988"

2.5 cm

3.490" 8.9 cm

Fig. 5

.330

.750 Shield

.975

Audio Return Audio Hot

Fig. 6

1.6"

Operation

If you want to use 12 to 18 V phantom power, it should be supplied through a center-tapped transformer (such as in the Crown PH-1A phan- tom supply) or directly from your mixer. This will ensure 70 dB of off-attenuation.

Typical placement for each microphone is at arm’s length from the user. Either place one microphone in front of each person or one between every two people. The front of the mi- crophone is indicated by an arrow on the bottom of the base plate.

Press near the center of the switch. The micro- phone will switch on or off according to how you set the slide switch. When the mic is on, the LED in the housing is lit.

The PCC-130SW includes two keyhole slots in its base to accept mounting screws.

1.Punch out the keyholes marked on the label underneath the base plate (use a razor blade, small screwdriver, etc.).

2.Using the template (Fig. 6), mark the loca-

tion of two holes in the table where you want to mount the mic. These holes are 1.6 inch (4.064 cm.) apart, center-to-center. They are 1.7 inch (4.318 cm) from the rear of the mic.

If your model is the SPP type install ¼-inch (6.35-mm) phone jacks in your table. Fig. 5 shows the optimum jack wiper locations.

Fig. 7

Dimensions are to outside of plastic housing.

		.450."
		1.14 cm
.483"
1.23 cm
		MOM.
		ON	1.661"
		MOM.	4.22 cm
		OFF
BOOST	CUT	PUSH ON
FLAT		PUSH OFF
BASS	TILT
		SWITCH
		FUNCTION

CUT OUT FOR

PERMANENT

INSTALLATION

PCCfi-130SW

PHASE COHERENT CARDIOIDfi

MADE IN USA

fi

1718 W. Mishawaka Road, Elkhart, IN 46517

(219) 294-8000

MICROPHONE FRONT

Architects’ and Engineers’ Specifications

The microphone shall be the Crown Model PCC- 130SW or equivalent. The microphone shall be a half-supercardioid electret condenser type.

The microphone shall employ the principle of phase coherency achieved by mounting a small-diameter element very near a boundary, thus eliminating comb filtering in the audible spectrum. The microphone will exhibit excellent off-axis response and gain-before-feedback.

A 15-foot (4.6 m), two-conductor shielded cable with TA3F and A3M connectors shall be supplied with the microphone. As an option, the microphone may be obtained with a bot- tom-mounted stereo phone plug (model PCC- 130SW/SPP, no cable provided).

Nominal sensitivity shall be 22 mV/Pa. Maxi- mum SPL shall be 120 dB SPL for 3% THD. Equivalent noise shall be 22 dBA nominal.

Frequency response shall be 50 Hz to 20,000 Hz with a uniform off-axis response, over 20 dB down at the rear nulls.

The PCC-130SW shall have a silent operating membrane switch which can be configured for push on/off, momentary on or momentary off operation. The Crown Model PCC-130SW is specified.

PCC-130SW

Warranty

Crown professional microphones are guaran- teed against malfunction for a period of three years from date of original purchase. Please refer to the enclosed full warranty sheet for more detail.

Service

If the microphone does not function properly, check that it is aimed correctly and is config- ured and connected as described in this data sheet. If there is hum or no signal, first repair or replace the cable. If it is determined that the microphone needs additional service and you wish to return it to Crown, a Service Return Authorization (SRA) is required. An SRA can be completed online at www.crownaudio.com/sup- port/factserv.htm. After securing an SRA, return the microphone in its original packaging to:

Crown Factory Service, 1718 W. Mishawaka Road, Elkhart, IN 46517-9439. For further assistance or technical support call 800-342- 6939.

Crown International

1718 W. Mishawaka Rd.

Elkhart, IN 46517-9439

TEL: 574-294-8000

FAX: 574-294-8FAX

©2006 Crown Audio®, Inc.

Specifications subject to change without prior notice. Latest information available at www.crownaudio.com. Crown, Crown Audio, PCC and Phase Coherent Cardioid are registered trademarks of Crown International, Inc.

11/06 101756-6