Crown Audio PZM-10LL specifications Mic Placement Mic Installation, Warranty, Service

Fig. 1®

PZMPZM-10 Frequency-10Response

Frequency in Hz

Fig. 2

PZM-10LL Frequency Response

Frequency in Hz

Mic Placement (continued)

For other placement suggestions, see the Crown Microphone Application Guide for Se- curity and Surveillance at www.crownaudio. com/mic_htm/mic_pubs.htm.

Mic Installation

1.Please refer to Fig. 3 and identify the parts shown.

2.Determine where you want to install the microphone, and drill a 25/32-inch diameter hole there.

3.PZM-10 only: Obtain some 2-conductor shielded mic cable, long enough to run from your equipment input to the microphone. If space is tight behind the mounting surface, obtain a right-angle female XLR connector. Solder the female XLR connector onto the cable: shield to pin 1, hot lead to pin 2, other lead to pin 3.

PZM-10LL only: Obtain enough mic cable to run from your equipment input to the mi- crophone. You can use either a 2-conductor shielded mic cable with a separate DC power lead, or a 3-conductor shielded mic cable (with one of the leads used for power).

4.Run the female XLR (if used) and mic cable to the hole.

5.Using a 5/32-in. Allen wrench, remove the collar from the microphone. Insert the micro- phone tube into the hole.

6.Slide the collar onto the mic tube. Pull the plate tight against the hole and press the collar tight against the mounting surface. Tighten the Allen screw in the collar.

7.PZM-10 only: Plug your mic cable into the microphone.

PZM-10LL only: Solder the PZM-10LL cable leads to your mic cable as described below:

Red to 12-24V DC White to Audio + lead Black to Audio – lead

Shield to cable shield and power supply –.

8.PZM-10 only: Plug the other end of your mic cable into one of these devices:

*A mic preamp that supplies phantom power.

*A mixer that supplies phantom power.

*A phantom power supply, such as the Crown PH-1A.

Connect the output of the supply to the mic input of your mic preamp, mixer or recorder.

Architects’ and Engineers’ Specifications PZM-10

The microphone shall be the Crown PZM-10 or equivalent. The microphone shall be a electret condenser Pressure Zone Micro- phone with a hemispherical polar pattern. The microphone shall have a tubular housing which mounts in a 25/32-in. diameter hole. Open-circuit sensitivity shall be 2.5 mV/Pa typical. Equivalent noise level shall be 26 dBA typical. Maximum SPL shall be 120

dB for 3% THD. Powering shall be 12-48 V phantom power. Output connector shall be male XLR-type. The Crown PZM-10 micro- phone is specified.

Architects’ and Engineers’ Specifications PZM-10LL

The microphone shall be the Crown PZM- 10LL or equivalent. The microphone shall be a electret condenser Pressure Zone Micro- phone with a hemispherical polar pattern. The microphone shall have a tubular housing which mounts in a 25/32-in. diameter hole. Open-circuit sensitivity shall be 1.4V/Pa typi- cal. Equivalent noise level shall be 26 dBA typical. Maximum SPL shall be 120 dB for 3% THD. Powering shall be 12-24 V DC. The microphone shall have a 12-in. unterminated cable. The Crown PZM-10LL microphone is specified.

Warranty

Crown professional microphones are guaran- teed against malfunction for a period of three years from date of original purchase. Please refer to the enclosed full warranty statement for more detail.

PZM-10

PZM-10LL

Service

If the unit fails to work, first replace or repair the mic cables and check the power sup- ply. A Service Return Authorization (SRA) is required for product being sent to the factory for service. An SRA can be completed on line at www.crownaudio.com/support/factserv. htm. If service is required, return the micro- phone in its original packaging to: Crown

Factory Service, 1718 West Mishawaka Road, Elkhart, Indiana 46517-9439. For further assistance or technical support call 800-342-6939.

Fig. 3 Dimensions

*

*2.450 in. (6.2 cm) in PZM-10LL

Crown International, Inc. 1718 W. Mishawaka Rd. Elkhart, IN 46517-9439 TEL: 574-294-8000 FAX: 574-294-8FAX www.crownaudio.com

©2008 Crown Audio®, Inc. Specifications subject to change without prior notice. Latest information available at www.crownaudio.com. Crown, Crown Audio, PZM and Pressure Zone Microphone are registered trademarks of Crown International. Pressure Recording Process is a trademark of E.M. Long Associates.

5/08 136932-4