Cub Cadet 1400E CLEANING TIPS - continued, Troubleshooting, Gardening Tools, Recommendations

CLEANING TIPS – continued

Barbecue Grills, Outdoor

Power Equipment &

Gardening Tools

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If using Cub Cadet All Purpose Cleaner or Degreaser, place detergent suction tube directly into cleaning solution and apply detergent at low pressure. Allow Cub Cadet detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure keeping the spray nozzle approximately 3-6 inches from the cleaning surface. For removing extremely stubborn dirt, it may be necessary to move the spray nozzle even closer to the surface for greater dirt cutting action. To remove caked on mud from garbage cans, lawn mower blades, wheelbarrows or other non-sensitive metal surfaces, you may want to use the Cub Cadet Dirtblaster® Wand.

9Caution: Do not use Dirtblaster® wand on cloth, plastic or other sensitive surfaces as it may cause damage.

Patio & Lawn Furniture

(with or without detergent)

Pre-rinse furniture and surrounding area with fresh water. If using Cub Cadet All Purpose Cleaner, place detergent suction tube direct- ly into cleaning solution and apply to surface at low pressure. Allow Cub Cadet All Purpose Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface.

If needed, use special Wash Brush Attachment to remove stubborn dirt. Rinse at high pressure in a sweeping motion keep- ing the spray nozzle approximately 3-6 inch- es from the cleaning surface. For best results, clean from top to bottom and from left to right. Caution: Do not use

Dirtblaster® wand on patio or lawn furni- ture as it may cause damage.

Recommendations

•Before cleaning any surface an inconspic- uous area should be cleaned to test spray pattern and distance for maximum clean- ing results.

•If painted surfaces are pealing or chipping, use extreme caution as pressure washer may remove the loose paint from the surface.

TROUBLESHOOTING

Disconnect the machine from the power source before making any repair.

Symptom	Cause	Solution
Motor will not start.	On/Off switch is in the “OFF”	Turn switch to the “ON” (I) position
	(O) position.
	Power cord is not plugged in.	Plug in power cord.
	Extension cord is too long.	Replace extension cord with either
	Extension cord is	a 25 ft. 12/2 gauge cord or a 50 ft. 10/2
	not proper gauge.	gauge cord.
	Extension cord is damaged.
	Electrical outlet does not supply	Try a different outlet.
	adequate power.
	Ground Fault Circuit Interrupter	Reset breaker (power supply)
	(GFCI) tripped.	or GFCI.
Unit does not reach	Diameter of garden hose	Replace with a 3/4 inch
high pressure.	is too small.	garden hose.
	Water supply is restricted.	Check garden hose for kinks,
		leaks and blockage.
			10
	Not enough inlet water supply.	Open water source full force.
	Water inlet filter is clogged.	Remove filter and rinse out
		in warm water.
	Spray wand is in low	Turn spray wand to high
	pressure position.	pressure position.
Output pressure	Not enough inlet water supply.	Turn water on full force. Check garden
varies high and low.		hose for kinks, leaks or blockage.
	Pump is sucking air.	Check that hoses and fittings are air tight.
		Turn off machine and purge pump by
		squeezing trigger gun until a steady flow
		of water emerges through the nozzle.
	Water inlet filter is clogged.	Remove filter and rinse out
		in warm water.
	Discharge nozzle	Blow out or remove debris
	is obstructed.	with a fine needle.
	Calcified gun, hose	Run distilled vinegar through
	or spray wand.	detergent suction tube.

Dealer Referral Line

1-877-835-7841

or visit our website: www.cubcadet.com