CyberPower Systems 2200E Functional Test, AC Mode, On-Battery Mode, Routine Maintenance, Storage

Functional Test

AC Mode

The UPS delivers power to the loads derived from the utility and maintains proper battery charge. It also regulates the output voltage to within a narrow range.

On-Battery Mode

The UPS operates on battery when the line voltage or frequency has fallen outside the limits. Local users are alerted to this mode of operation by visual and audible indicators. The UPS provides power to the load from the battery and through its inverter and the output voltage and frequency of the UPS are regulated within a narrow range

1.Switch On

Press the power switch on the front panel then the status LCD will light up.

2.Switch Off

Press again the power switch, the status LCD on the front panel will go off.

3.Cold Start / Start on Battery:

This UPS can be turned on even when AC is not present.

Press the power switch on the front panel then the status LCD will light up.

ROUTINE MAINTENANCE AND STORAGE

ROUTINE MAINTENANCE

1.Use dry soft clothes to clean the front panel and plastic parts. Do not use any detergent that contains alcoholic ingredient.

2.The expected lifetime of the battery is around 3 years. Improper operation and harsh environment will reduce the actual lifetime.

3.Unplug the UPS from power inlet if the UPS will not operate for long period of time.

STORAGE

1.First turn off your UPS and disconnect its power cord from the wall outlet. Disconnect all cables connected the UPS to avoid battery drain.

2.The UPS should be stored in a cool dry location.

3.Make sure the battery is fully charged before the UPS is stored.

4.For extended storage in moderate climates, the battery should be charged for 12 hours every 3 months by plugging the power cord into the wall receptacle and turning on the main switch. Repeat it every 2 months in high temperature locations.

TROUBLE SHOOTING

Problem	Possible Cause	Solution
The UPS does	Batteries are not fully	Recharge the battery by leaving the UPS
	charged.	plugged in.
not perform
expected	Battery is slightly worn out.	Contact CyberPower Systems at
runtime.
		service@cyberpower-eu.com
	The on/off switch is	Turn the UPS off. Wait 10 seconds and
	designed to prevent
	damage by rapidly turning it	then turn the UPS on.
	off and on.
The UPS will not	The unit is not connected to	The unit must be connected to a
turn on.	an AC outlet.	220-240V 50/60Hz outlet.
	The battery is worn out.	Contact CyberPower Systems at
		service@cyberpower-eu.com
	Mechanical problem.	Contact CyberPower Systems at
		service@cyberpower-eu.com
	Circuit breaker is tripped	Turn the UPS off and unplug at least one
		piece connected equipment. Unplug the
	due to overload	power cord of the UPS then press the
Outlets do not		circuit breaker knob.
provide power to	Batteries are discharged	Allow the unit to recharge for at least 4
equipment		hours.
	Unit has been damaged by	Contact CyberPower Systems at
	a surge or spike.	service@cyberpower-eu.com
	The serial/USB cable is not	Connect the serial/USB cable to the UPS
		unit and an open serial port on the back
	connected.	of the computer. You must use the cable
		that came with the unit.
PowerPanel®	The serial/USB cable is	Try another serial/USB port of your
	connected to the wrong
Personal Edition	port.	computer.
is inactive (all
		Shutdown your computer and turn the
icons are gray).	The unit is not providing
		UPS off. Wait 10 seconds and turn the
	battery power.
		UPS back on. This should reset the unit.
	The serial cable is not the	You must use the cable included with the
	cable that was provided with
		unit for the software.
	the unit.

CyberPower warrants to you, the original purchaser, that CyberPower UPS will be free from defects in design, assembly, materials and workmanship for two years ( battery is only one year) from the date of original purchase. Any warranty services, please contact your local dealers or distributors.

TECHNICAL SPECIFICATIONS

Model		Value 1200E	Value 1500E	Value 2200E
Capacity	(VA)	1200VA	1500VA	2200VA
Capacity	(Watts)	720W	900W	1320W
Input
Input Voltage Range			160VAC~270VAC
Frequency Range		50/60Hz +/-3Hz(Auto Sensing)
Output
On Battery Output		Simulated Sine Wave at 230Vac +/-7%
Voltage
On Battery Output			50/60 Hz
Frequency
Overload Protection		On Utility: Circuit Breaker, On Battery: Internal Current Limiting
Physical
Total # of UPS			(6) IEC 320 C13
Receptacles
Maximum Dimensions		32.6cm(L) × 14.cm(W) × 18cm(H)
Weight		13.0 kg / 28.6 Lbs	14.3 kg / 31.5 Lbs	15.4 kg / 33.9 Lbs
Battery
Sealed Maintenance		12V / 7Ah x2	12V / 8.5Ah x2	12V / 9Ah x2
Free Lead Acid Battery
Typical Recharge Time			8 Hours
Warning Diagnostics
Indicators		Power On, UPS Status Display, Capacity Display, Digital Value
			Display
Audible Alarms		On Battery, Low Battery, Overload
Environmental
Operating Temperature		+32°F to 104°F ( 0°C to 40°C )
Operating Relative		0 to 95% NON-CONDENSING
Humidity
Communication
PowerPanel® Personal		Windows 98/ME/2000/NT/XP/Vista
Edition Software
Management
Auto-Charger			Yes
Auto-Restart			Yes
USB			Yes

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

LCD Indication

Line mode

Select SW		UPS Status Display			Capacity Display			Digital Value Display
Press					Load	Battery	Input	Output	Run	%	%
					Cap.	Cap.	Voltage	Voltage	Time	of Load	of Batt.
Initial	V	X	--	X	V	X		V
1st	V	X	--	X	V	X			V
2nd	V	X	--	X	V	X				V
3rd	V	X	--	X	X	V					V
4th	V	X	--	X	V	X	V
5th(Return)	V	X	--	X	V	X		V
Press >3sec	V	X	V	X	--	--	--	--	--	--	--
(Sound Disable)
Press >3sec
again	V	X	X	X	--	--	--	--	--	--	--
(Sound Enable)
(Overload)	V	X	--	V	--	--	--	--	--	--	--
“V” : Illuminated,	“X” : Not Illuminated,			“--“ : Either

Battery mode

Select SW		UPS Status Display			Capacity Display			Digital Value Display
Press					Load	Battery	Input	Output	Run	%	%
					Cap.	Cap.	Voltage	Voltage	Time	of Load	of Batt.
Initial	X	V	--	X	X	V		V
1st	X	V	--	X	X	V			V
2nd	X	V	--	X	V	X				V
3rd	X	V	--	X	X	V					V
4th	X	V	--	X	X	V	V
5th(Return)	X	V	--	X	X	V		V
Press >3sec	X	V	V	X	--	--	--	--	--	--	--
(Sound Disable)
Press >3sec
again	X	V	X	X	--	--	--	--	--	--	--
(Sound Enable)
(Overload)	X	V	--	V	--	--	--	--	--	--	--
“V” : Illuminated,	“X” : Not Illuminated,			“--“ : Either

For more information, visit eu.cyberpowersystems.com or contact

CyberPower Systems B.V.

Flight Forum 3545 5657DW Eindhoven The Netherlands

Tel: +31 40 2348170, E-MAIL: sales@cyberpower-eu.com

CyberPower Systems Inc. (USA) 4241 12th Avenue East, Suite 400, Shakopee, MN 55379, U.S.A. Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL: sales@cyberpowersystems.com

Entire contents copyright ©2004 CyberPower Systems B.V., All rights reserved. Reproduction in whole or in part without permission is prohibited. PowerPanel® and PowerPanel® Plus are trademarks of CyberPower Systems (USA) Inc.