CyberPower Systems UP550UI, UP750UI, UP425UIT Technical Specifications, Shootingo Ting, Storage

BATTERY REPLACEMENT PROCEDURE:

1. Remove the 2 retaining screws then push the battery cover backward and remove the cover.

2. Lean the UPS to one side and pull out the battery partially from the compartment. Disconnect the battery wires from the battery, and then remove the battery from the compartment.

3. Install the replacement battery by connecting the red wire to the positive (+) terminal of the battery and connecting the black wire to the negative (-) terminal of the battery.

4. Slide the battery back into the compartment. Turn the UPS upside down to help the batteries entirely slide into the compartment. Replace the cover and the retaining screws.

REMINDER: Recharge the unit for 4 – 8 hours to ensure the UPS performs expected runtime

STORAGE

First turn off your UPS and disconnect its power cord from the wall outlet. Disconnect all cables connected the UPS to avoid battery drain. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to insure battery life. If the battery remains uncharged for an extended period of time, it may suffer permanent loss of capacity.

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS

Model	UP425UIT	UP550UI	UP750UI
Capacity (VA)	425VA	550VA	750VA
Capacity (Watts)	255W	330W	450W
Input
Input Voltage Range	160Vac - 278Vac (User Configuration)
Frequency Range		50 / 60 Hz
Output
On Battery Output Voltage	Simulated Sine Wave at 230Vac +/- 5%
On Battery Output Frequency		50/60 Hz +/- 1%
Overload Protection	On Utility: Fuse, On Battery: Internal Current Limiting
Surge Protection and Filtering
Lightning / Surge Protection		Yes
Network Protection	RJ11/RJ45 (One In/One Out)
Physical
Total # of UPS Receptacles	2 (UPS) + 1 (Surge)	3 (UPS) + 1 (Surge)
Maximum Dimensions (cm)	23.8 x 8.0 x 13.7	28.3 x 9.1 x 16.4
Weight (Kg)	5	6.8	7.5
Battery
Sealed Maintenance Free	12V / 4.5 AH x1	12V / 8 AH x1	12V / 9 AH x1
Lead Acid Battery
User Replaceable	No	Yes, Hot Swappable Battery Pack
Typical Recharge Time		8 Hours
Warning Diagnostics
Indicators	Power on, Using Battery, Overload, Replace Battery
Audible Alarms	On Battery, Low Battery, Overload
Environmental
Operating Temperature	32 F to 95 F ( 0 C to 35 C )
Operating Relative Humidity	0 to 95% Non-Condensing
Communication
PowerPanel Personal	Windows 98/ME/2000/NT/XP/Server 2003/Vista
Edition Software
Management
Self-Test		Yes
USB		Yes
Auto-Charger		Yes
Auto-Restart		Yes

All specifications are subject to change without notice.

	TROUBLETROUB	SHOOTINGO TING
Problem	Possible Cause		Solutions
The UPS does not	Batteries are not fully		Recharge the battery by leaving the UPS
perform expected	charged.		plugged in.
runtime.
	Battery is slightly worn out.		Contact CyberPower Systems at
			service@cyberpower-eu.com.
The UPS will not	The on/off switch is		Turn the UPS off. Wait 10 seconds and then
turn on.	designed to prevent		turn the UPS on.
	damage by rapidly turning it
	off and on.
	The unit is not connected to		The unit must be connected to a 220-240V
	an AC outlet.		50/60Hz outlet.
	The battery is worn out.		Contact CyberPower Systems at
			service@cyberpower-eu.com
	Mechanical problem.		Contact CyberPower Systems at
			service@cyberpower-eu.com
Outlets do not	Fuse is blown due to		Turn the UPS off and unplug at least one piece
provide power to	overload.		of equipment. Unplug the power cord of the
equipment			UPS then remove the fuse compartment
			beneath the power inlet of the UPS and
			replace the blown fuse with a spare one. Lock
			the compartment back to the UPS. Connect
			power cord then turn the UPS on. Make sure
			that your spare fuse meets the specification :
			6.3A, 250V, 5x10mm.
	Batteries are discharged.		Allow the unit to recharge for at least 4 hours.
	Unit has been damaged by		Contact CyberPower Systems at
	a surge or spike.		service@cyberpower-eu.com.
PowerPanel	The USB cable is not		Connect the USB cable to the UPS unit and an
Personal Edition is	connected.		open USB port on the back of the computer.
inactive (all icons			You must use the cable that came with the
are gray).			unit.
	The USB cable is		Try another USB port of your computer.
	connected to the wrong
	port.
	The unit is not providing		Shut down your computer and turn the UPS
	battery power.		off. Wait 10 seconds and turn the UPS back
			on. This should reset the unit.
	The USB cable is not the		You must use the cable included with the unit
	cable that was provided		for the software.
	with the unit.

For more information, please contact:

CyberPower Systems ( USA ), Inc. 4241 12th Avenue East Suite 400 Shakopee, MN 55379 CyberPower Systems B. V. ( Europe ) Flight Forum 3545,5657DW Eindhoven,The Netherlands

DEFINITIONS FOR ILLUMINATED LED INDICATORS

Power	Using		Replace		Overload	Fuse	Alarm	Condition
On	Battery		Battery
On		Off		Off	Off	Normal	Off	Normal
Off		On		Off	Off	Normal	Two Beeps	Utility Failure- The UPS is providing
								battery power to battery-power
								supplied outlets.
Off		On		Off	Off	Normal	Rapid	Utility Failure- The UPS is providing
							Beeps	battery power. Rapid beeps indicate
								the unit will run out of power shortly.
On		Off		Off	On	Blown	Long Beeps	System Overload- Occurs in the
								full-time surge protection outlet. Turn
								the UPS off, unplug at least one piece
								of equipment from UPS. Replace the
								fuse with the spare one then turn the
								UPS on.
Off		On		Off	On	Normal	Long Beeps	Battery Overload- Occurs when
								connected equipment exceeds the
								rating of battery outlets of the unit.
								Turn the UPS off, unplug at least one
								piece of equipment from battery
								outlets. Check the fuse and do the
								replacement if necessary. Turn the
								UPS on.
On		Off		On	Off	Normal	Beep	Replace Battery- UPS battery is no
								longer useful and must be replaced.
								Please see manual “Battery
								replacement procedure”.

CyberPower warrants to you, the original purchaser, that CyberPower UPS will be free from defects in design, assembly, materials and workmanship for two years ( battery is only one year) from the date of original purchase. Any warranty services, please contact your local dealers or distributors.

Phone: (952)403-9500	Fax: (952)403-0009	www.cyberpowersystems.com
Phone: 31 (0)40 2348170	Fax: 31 (0)40 2340314	eu.cyberpowersystems.com

Entire contents copyright ©2005 CyberPower Systems B.V., All rights reserved. Reproduction in whole or in part without permission is prohibited. PowerPanel and PowerPanel Plus are trademarks of CyberPower Systems (USA) Inc.