Dacor DR30GIFS manual

COMBINATION INSTALLATIONS

Document # PGCI-028		Revised 10/07/13 Page 1/1
	DR30GI[F]S Range with ERV3015	PLANNING
	Raised Vent	GUIDE

Raised Vent (Self-Rimming) Installation Cutout Options (Models DR30GIS and DR30GIFS Only)

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

For all installations with a raised vent:

Countertop height: 34 3/4” (88.3 cm) min. 36 7/8” (93.7 cm) max.

Countertop thickness: 1 5/8” (4.1 cm) max.

NOTE: For all raised vent installations, use only Dacor raised vent model ERV3015. This configuration is not compatible with cabinet blower model CABP3.

10” min. (25.4 cm)				Rear wall or		3/8” (9.5 mm) min.
to any combustibles
				countertop edge		countertop overhang
above counter both sides
		27 1/2” (69.9 cm)
	r	aised vent openin			g
					1
								3”
		29 1/4” (74.3 cm)
								(7.6 cm)
		countertop opening
						20	5/8”
			30” (76.2 cm)
						(52.4 cm)
			cabinet opening
			below countertop

Cabinet face

below countertop

Notch countertop overhang to width of

cabinets Countertop overhang 1 5/8” (4.1 cm) max.

24” - 24 1/4” Cabinet Depth

Partial Side Panels Installed (Top View)2, 3

10” min. (25.4 cm)		Rear wall or
to any combustibles
above counter both sides		countertop edge
	3/8” (9.5 mm) min.		3” (7.6 cm)
	countertop overhang

			3/8” min. (1.0 cm) flat countertop
			overhang required behind cutout
		Wall					29 1/2” (74.9 cm)
Stiffener								Countertop
	ERV3015
								Back of
	raised vent			DR30GI[F]S				control panel
						range		Cabinet face
							Shown with partial
							side panel installed
					3/8” min. (1.0 cm)
					space behind raised vent
					chassis to clear stiffener

IMPORTANT: If optional side panels are not installed cabinet face must be flush with back of control panel.

Side View - DR30GI[F]S Range and

ERV3015 Raised Vent

10” min. (25.4 cm)	Rear wall or	3/8” (9.5 mm) min.
to any combustibles
	countertop edge	countertop overhang
above counter both sides

			27 1/2” (69.9 cm)
		r	aised vent openin			g
						1
			29 1/4” (74.3 cm)						20		7/8”
			countertop opening				20	5/8”	(53.0		cm)
	25 3/4”
					30” (76.2 cm)		(52.4	cm)		to
	(65.4 cm)
	max.			cabinet opening						24 1/8”
			below countertop						(61.3 cm)
			Notch countertop
		overhang to width of
					cabinets
					Cabinet face
Countertop
			below countertop
	front

24 1/4” - 27 1/2” Cabinet Depth

Partial Side Panels Installed (Top View)4

	27 1/2” (69.9 cm)
r	aised vent openin		g
			1
							3”
	29 1/4” (74.3 cm)
							(7.6 cm)
	countertop opening
				24		1/8”
		30” (76.2 cm)
					(61.3 cm)
		cabinet opening
		below countertop

Cabinet face

below countertop

Notch countertop overhang to width of

cabinets Countertop overhang 1 5/8” (4.1 cm) max.

Custom Cabinet 27 1/2” or Deeper,

Partial Side Panels Removed (Top View)4

1To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm). Width notches remains 30”.

2For 24 to 24 1/4 inch deep cabinets, the side panels and control panel will protrude from the cabinet face a total of 5 5/8 inches.

3Revision A ranges only: Raised vent trim piece and 3 1/2 inch side panels (Dacor PN ADTK30GSR24) must be installed to cover the front of the raised vent chassis in back and range chassis on sides.

4Revision A ranges only: Optional raised vent trim piece (Dacor PN ADTK30GSR) must be installed to cover the front of the raised vent chassis in back.

All specifications subject to change without notice. www.dacor.com Phone: (800) 793-0093