Dacor ERWD, EWD, OWD, RWDV warning, Observe all governing codes and ordinances, during planning and installation. Contact your, local building department for further information

DWD, ERWD, EWD, IWD, MRWD,

Document # PG02-002

MWDH, MWDV, OWD, RWDV

Revised 01/18/12 Page 3/3

24”, 27”, 30”, 36” Wide

PLANNING

Warming Drawers

GUIDE

Cabinet/countertop tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated

warning

•

Observe all governing codes and ordinances

3/4" min.*

during planning and installation. Contact your

Warming

(1.9 cm)

local building department for further information.

C

drawer

36" typ.

D

•

This appliance must be installed in accordance

(91.4 cm)

Warming

120 Vac

with the accompanying installation instructions.

C

drawer

electrical

outlet

3/4" min.*

Mounting platform must be 3/4" (1.9 cm) thick

(1.9 cm)

and support 100 lbs.

A

B

Cooktop

1 1/2" (3.8 cm)

27"/30"/36" Dacor

Typical countertop

single wall oven

3/4” min.*

D

Warming

(1.9 cm)

Warming

120 Vac

drawer

C

C

drawer

elect.

D

36" typ.

120 Vac

Warming

120 Vac

91.4 cm)

A

electrical

C

drawer

elect.

B

outlet

Toe kick

3/4" min.*

A

(1.9 cm)

(B) Min. Width to

(D) Min. Vertical Gap

Model

(A) Cutout Width

Adjacent Doors/

(C) Cutout Height

Min. Cutout Depth

Between Cutouts

Drawers

DWD30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

ERWD27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

ERWD30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD24

22 1/2” (57.2 cm)

24 1/4” (61.6 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD36****

34 1/2” (87.6 cm)

36 1/4” (92.1 cm)*

9 1/8” (23.2 cm)

NA

IWD24

22 1/2” (57.2 cm)

**

9 1/8” (23.2 cm)

1 1/16” (2.7 cm)

24” (61.0 cm)

IWD27

25 1/2” (64.8 cm)

**

9 1/8” (23.2 cm)

1 1/16” (2.7 cm)

IWD30

28 1/2” (72.4 cm)

**

9 1/8” (23.2 cm)

1 1/16” (2.7 cm)

MRWD27

25 1/2” (64.8 cm)

27” (68.6 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MRWD30

28 1/2” (72.4 cm)

30” (76.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDH27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDH30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDV27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDV30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

OWD24*****

22 5/8” (57.5 cm)

24 1/4” (61.6 cm)***

11 15/16” (30.3 cm)

NA

20 1/8” (51.1 cm)

RWDV30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

24” (61.0 cm)

*Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERWD, EWD, MRWD, MWDH, MWDV and RWDV series models.

**On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout.

The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the

custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.

*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.

**** Model EWD36 cannot be installed above or below another warming drawer (any type).

***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type).

All specifications subject to change without notice. www.dacor.com Phone: (800) 793-0093